Peler

: / usr / share / snmp / mibs / ietf /
Filename : FDDI-SMT73-MIB
back
FDDI-SMT73-MIB DEFINITIONS ::= BEGIN

IMPORTS
        Counter
            FROM RFC1155-SMI
	transmission
	    FROM RFC1213-MIB
        OBJECT-TYPE
            FROM RFC-1212;

--  This MIB module uses the extended OBJECT-TYPE macro as
--  defined in [7].

-- this is the FDDI MIB module

fddi    OBJECT IDENTIFIER ::= { transmission 15 }
fddimib   OBJECT IDENTIFIER ::= { fddi 73 }

-- textual conventions

FddiTimeNano ::= INTEGER (0..2147483647)
-- This data type specifies 1 nanosecond units as
-- an integer value.
--
-- NOTE: The encoding is normal integer representation, not
-- two's complement.  Since this type is used for variables
-- which are encoded as TimerTwosComplement in the ANSI
-- specification, two operations need to be performed on such
-- variables to convert from ANSI form to SNMP form:
--
-- 1) Convert from two's complement to normal integer
--    representation
-- 2) Multiply by 80 to convert from 80 nsec to 1 nsec units
--
-- No resolution is lost.  Moreover, the objects for which
-- this data type is used effectively do not lose any range
-- due to the lower maximum value since they do not require
-- the full range.
--
-- Example: If fddimibMACTReq had a value of 8 ms, it would
-- be stored in ANSI TimerTwosComplement format as 0xFFFE7960
-- [8 ms is 100000 in 80 nsec units, which is then converted
-- to two's complement] but be reported as 8000000 in SNMP
-- since it is encoded here as FddiTimeNano.

FddiTimeMilli ::= INTEGER (0..2147483647)
-- This data type is used for some FDDI timers. It specifies
-- time in 1 millisecond units, in normal integer
-- representation.

FddiResourceId ::= INTEGER (0..65535)
-- This data type is used to refer to an instance of a  MAC,
-- PORT, or PATH Resource ID.  Indexing begins
-- at 1.  Zero is used to indicate the absence of a resource.

FddiSMTStationIdType ::= OCTET STRING (SIZE (8))
-- The unique identifier for the FDDI station.  This is a
-- string of 8 octets, represented as X' yy yy xx xx xx xx
-- xx xx' with the low order 6 octet (xx) from a unique IEEE
-- assigned address.  The high order two bits of the IEEE
-- address, the group address bit and the administration bit
-- (Universal/Local) bit should both be zero.  The first two
-- octets, the yy octets, are implementor-defined.
--
-- The representation of the address portion of the station id
-- is in the IEEE (ANSI/IEEE P802.1A) canonical notation for
-- 48 bit addresses.  The canonical form is a 6-octet string
-- where the first octet contains the first 8 bits of the
-- address, with the I/G(Individual/Group) address bit as the
-- least significant bit and the  U/L (Universal/Local) bit
-- as the next more significant bit, and so on.  Note that
-- addresses in the ANSI FDDI standard SMT frames are
-- represented in FDDI MAC order.

FddiMACLongAddressType ::= OCTET STRING (SIZE (6))
-- The representation of long MAC addresses as management
-- values is in the IEEE (ANSI/IEEE P802.1A) canonical
-- notation for 48 bit addresses.  The canonical form is a
-- 6-octet string where the first octet contains the first 8
-- bits of the address, with the I/G (Individual/Group)
-- address bit as the least significant bit and the  U/L
-- (Universal/Local) bit as the next more significant bit,
-- and so on.  Note that the addresses in the SMT frames are
-- represented in FDDI MAC order.

-- groups in the FDDI MIB module

fddimibSMT          OBJECT IDENTIFIER ::= { fddimib 1 }

fddimibMAC          OBJECT IDENTIFIER ::= { fddimib 2 }

fddimibMACCounters  OBJECT IDENTIFIER ::= { fddimib 3 }

fddimibPATH         OBJECT IDENTIFIER ::= { fddimib 4 }

fddimibPORT         OBJECT IDENTIFIER ::= { fddimib 5 }

-- the SMT group
-- Implementation of the SMT group is mandatory for all
-- systems which implement manageable FDDI subsystems.

fddimibSMTNumber OBJECT-TYPE
    SYNTAX  INTEGER (0..65535)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The number of SMT implementations (regardless of
            their current state) on this network management
            application entity.  The value for this variable
            must remain constant at least from one re-
            initialization of the entity's network management
            system to the next re-initialization."
    ::= { fddimibSMT  1 }

-- the SMT table

fddimibSMTTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF FddimibSMTEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
            "A list of SMT entries.  The number of entries
            shall not exceed the value of fddimibSMTNumber."
    ::= { fddimibSMT  2 }

fddimibSMTEntry OBJECT-TYPE
    SYNTAX  FddimibSMTEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
            "An SMT entry containing information common to a
            given SMT."
    INDEX   { fddimibSMTIndex }
    ::= { fddimibSMTTable 1 }

FddimibSMTEntry ::=
    SEQUENCE {
        fddimibSMTIndex
            INTEGER,
        fddimibSMTStationId
            FddiSMTStationIdType,
        fddimibSMTOpVersionId
            INTEGER,
        fddimibSMTHiVersionId
            INTEGER,
        fddimibSMTLoVersionId
            INTEGER,
        fddimibSMTUserData
            OCTET STRING,
        fddimibSMTMIBVersionId
            INTEGER,
        fddimibSMTMACCts
            INTEGER,
        fddimibSMTNonMasterCts
            INTEGER,
        fddimibSMTMasterCts
            INTEGER,
        fddimibSMTAvailablePaths
            INTEGER,
        fddimibSMTConfigCapabilities
            INTEGER,
        fddimibSMTConfigPolicy
            INTEGER,
        fddimibSMTConnectionPolicy
            INTEGER,
        fddimibSMTTNotify
            INTEGER,
        fddimibSMTStatRptPolicy
            INTEGER,
        fddimibSMTTraceMaxExpiration
            FddiTimeMilli,
        fddimibSMTBypassPresent
            INTEGER,
        fddimibSMTECMState
            INTEGER,
        fddimibSMTCFState
            INTEGER,
        fddimibSMTRemoteDisconnectFlag
            INTEGER,
        fddimibSMTStationStatus
            INTEGER,
        fddimibSMTPeerWrapFlag
            INTEGER,
        fddimibSMTTimeStamp
            FddiTimeMilli,
        fddimibSMTTransitionTimeStamp
            FddiTimeMilli,
        fddimibSMTStationAction
            INTEGER
    }

fddimibSMTIndex OBJECT-TYPE
    SYNTAX  INTEGER (1..65535)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "A unique value for each SMT.  The value for each
            SMT must remain constant at least from one re-
            initialization of the entity's network management
            system to the next re-initialization."
    ::= { fddimibSMTEntry 1 }

fddimibSMTStationId OBJECT-TYPE
    SYNTAX  FddiSMTStationIdType -- OCTET STRING (SIZE (8))
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "Used to uniquely identify an FDDI station."
    REFERENCE
            "ANSI { fddiSMT 11 }"
    ::= { fddimibSMTEntry 2 }

fddimibSMTOpVersionId OBJECT-TYPE
    SYNTAX  INTEGER (1..65535)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The version that this station is using for its
            operation (refer to ANSI 7.1.2.2). The value of
            this variable is 2 for this SMT revision."
    REFERENCE
            "ANSI { fddiSMT 13 }"
    ::= { fddimibSMTEntry 3 }

fddimibSMTHiVersionId OBJECT-TYPE
    SYNTAX  INTEGER (1..65535)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The highest version of SMT that this station
            supports (refer to ANSI 7.1.2.2)."
    REFERENCE
            "ANSI { fddiSMT 14 }"
    ::= { fddimibSMTEntry 4 }

fddimibSMTLoVersionId OBJECT-TYPE
    SYNTAX  INTEGER (1..65535)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The lowest version of SMT that this station
            supports (refer to ANSI 7.1.2.2)."
    REFERENCE
            "ANSI { fddiSMT 15 }"
    ::= { fddimibSMTEntry 5 }

fddimibSMTUserData OBJECT-TYPE
    SYNTAX  OCTET STRING (SIZE (32))
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
            "This variable contains 32 octets of user defined
            information. The information shall be an ASCII
            string."
    REFERENCE
            "ANSI { fddiSMT 17 }"
    ::= { fddimibSMTEntry 6 }

fddimibSMTMIBVersionId OBJECT-TYPE
    SYNTAX  INTEGER (0..65535)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The version of the FDDI MIB of this station.  The
            value of this variable is 1 for this SMT
            revision."
    REFERENCE
            "ANSI { fddiSMT 18 }"
    ::= { fddimibSMTEntry 7 }

fddimibSMTMACCts OBJECT-TYPE
    SYNTAX  INTEGER (0..255)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The number of MACs in this station or
            concentrator."
    REFERENCE
            "ANSI { fddiSMT 21 }"
    ::= { fddimibSMTEntry 8 }

fddimibSMTNonMasterCts OBJECT-TYPE
    SYNTAX  INTEGER (0..2)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The value of this variable is the number of A, B,
            and S ports in this station or concentrator."
    REFERENCE
            "ANSI { fddiSMT 22 }"
    ::= { fddimibSMTEntry 9 }

fddimibSMTMasterCts OBJECT-TYPE
    SYNTAX  INTEGER (0..255)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The number of M Ports in a node. If the node is
            not a concentrator, the value of the variable is
            zero."
    REFERENCE
            "ANSI { fddiSMT 23 }"
    ::= { fddimibSMTEntry 10 }

fddimibSMTAvailablePaths OBJECT-TYPE
    SYNTAX  INTEGER (0..7)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "A value that indicates the PATH types available
            in the station.

            The value is a sum.  This value initially takes
            the value zero, then for each type of PATH that
            this node has available, 2 raised to a power is
            added to the sum.  The powers are according to the
            following table:

                     Path   Power
                  Primary     0
                Secondary     1
                    Local     2

            For example, a station having Primary and Local
            PATHs available would have a value of 5 (2**0 +
            2**2)."
    REFERENCE
            "ANSI { fddiSMT 24 }"
    ::= { fddimibSMTEntry 11 }

fddimibSMTConfigCapabilities OBJECT-TYPE
    SYNTAX  INTEGER (0..3)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "A value that indicates the configuration
            capabilities of a node. The 'Hold Available' bit
            indicates the support of the optional Hold
            Function, which is controlled by
            fddiSMTConfigPolicy.  The 'CF-Wrap-AB' bit
            indicates that the station has the capability of
            performing a wrap_ab (refer to ANSI SMT 9.7.2.2).

            The value is a sum.  This value initially takes
            the value zero, then for each of the configuration
            policies currently enforced on the node, 2 raised
            to a power is added to the sum.  The powers are
            according to the following table:

                       Policy   Power
                holdAvailable     0
                   CF-Wrap-AB     1 "
    REFERENCE
            "ANSI { fddiSMT 25 }"
    ::= { fddimibSMTEntry 12 }

fddimibSMTConfigPolicy OBJECT-TYPE
    SYNTAX  INTEGER (0..1)
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
            "A value that indicates the configuration policies
            currently desired in a node.  'Hold' is one of the
            terms used for the Hold Flag, an optional ECM flag
            used to enable the optional Hold policy.

            The value is a sum.  This value initially takes
            the value zero, then for each of the configuration
            policies currently enforced on the node, 2 raised
            to a power is added to the sum.  The powers are
            according to the following table:

                           Policy   Power
                configurationhold     0 "
    REFERENCE
            "ANSI { fddiSMT 26 }"
    ::= { fddimibSMTEntry 13 }

fddimibSMTConnectionPolicy OBJECT-TYPE
    SYNTAX  INTEGER (32768..65535)
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
            "A value representing the connection policies in
            effect in a node. A station sets the corresponding
            bit for each of the connection types that it
            rejects. The letter designations, X and Y, in the
            'rejectX-Y' names have the following significance:
            X represents the PC-Type of the local PORT and Y
            represents the PC_Type of the adjacent PORT
            (PC_Neighbor). The evaluation of Connection-
            Policy (PC-Type, PC-Neighbor) is done to determine
            the setting of T- Val(3) in the PC-Signalling
            sequence (refer to ANSI 9.6.3). Note that Bit 15,
            (rejectM-M), is always set and cannot be cleared.

            The value is a sum.  This value initially takes
            the value zero, then for each of the connection
            policies currently enforced on the node, 2 raised
            to a power is added to the sum.  The powers are
            according to the following table:

                   Policy   Power
                rejectA-A     0
                rejectA-B     1
                rejectA-S     2
                rejectA-M     3
                rejectB-A     4
                rejectB-B     5
                rejectB-S     6
                rejectB-M     7
                rejectS-A     8
                rejectS-B     9
                rejectS-S     10
                rejectS-M     11
                rejectM-A     12
                rejectM-B     13
                rejectM-S     14
                rejectM-M     15 "
    REFERENCE
            "ANSI { fddiSMT 27 }"
    ::= { fddimibSMTEntry 14 }

fddimibSMTTNotify OBJECT-TYPE
    SYNTAX  INTEGER (2..30)
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
            "The timer, expressed in seconds, used in the
            Neighbor Notification protocol. It has a range of
            2 seconds to 30 seconds, and its default value is
            30 seconds (refer to ANSI SMT 8.2)."
    REFERENCE
            "ANSI { fddiSMT 29 }"
    ::= { fddimibSMTEntry 15 }

fddimibSMTStatRptPolicy OBJECT-TYPE
    SYNTAX  INTEGER { true(1), false(2) }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
            "If true, indicates that the node will generate
            Status Reporting Frames for its implemented events
            and conditions. It has an initial value of true.
            This variable determines the value of the
            SR_Enable Flag (refer to ANSI SMT 8.3.2.1)."
    REFERENCE
            "ANSI { fddiSMT 30 }"
    ::= { fddimibSMTEntry 16 }

fddimibSMTTraceMaxExpiration OBJECT-TYPE
    SYNTAX  FddiTimeMilli
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
            "Reference Trace_Max (refer to ANSI SMT
            9.4.4.2.2)."
    REFERENCE
            "ANSI { fddiSMT 31 }"
    ::= { fddimibSMTEntry 17 }

fddimibSMTBypassPresent OBJECT-TYPE
    SYNTAX  INTEGER { true(1), false(2) }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "A flag indicating if the station has a bypass on
            its AB port pair."
    REFERENCE
            "ANSI { fddiSMT 34 }"
    ::= { fddimibSMTEntry 18 }

fddimibSMTECMState OBJECT-TYPE
    SYNTAX  INTEGER {
                ec0(1), -- Out

                ec1(2), -- In
                ec2(3), -- Trace
                ec3(4), -- Leave
                ec4(5), -- Path_Test
                ec5(6), -- Insert
                ec6(7), -- Check
                ec7(8)  -- Deinsert
            }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "Indicates the current state of the ECM state
            machine (refer to ANSI SMT 9.5.2)."
    REFERENCE
            "ANSI { fddiSMT 41 }"
    ::= { fddimibSMTEntry 19 }

fddimibSMTCFState OBJECT-TYPE
    SYNTAX  INTEGER {
                cf0(1),   -- isolated
                cf1(2),   -- local_a
                cf2(3),   -- local_b
                cf3(4),   -- local_ab
                cf4(5),   -- local_s
                cf5(6),   -- wrap_a
                cf6(7),   -- wrap_b
                cf7(8),   -- wrap_ab
                cf8(9),   -- wrap_s
                cf9(10),  -- c_wrap_a
                cf10(11), -- c_wrap_b
                cf11(12), -- c_wrap_s
                cf12(13)  -- thru
            }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The attachment configuration for the station or
            concentrator (refer to ANSI SMT 9.7.2.2)."
    REFERENCE
            "ANSI { fddiSMT 42 }"
    ::= { fddimibSMTEntry 20 }

fddimibSMTRemoteDisconnectFlag OBJECT-TYPE
    SYNTAX  INTEGER { true(1), false(2) }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "A flag indicating that the station was remotely

            disconnected from the network as a result of
            receiving an fddiSMTAction, disconnect (refer to
            ANSI SMT 6.4.5.3) in a Parameter Management Frame.
            A station requires a Connect Action to rejoin and
            clear the flag (refer to ANSI SMT 6.4.5.2)."
    REFERENCE
            "ANSI { fddiSMT 44 }"
    ::= { fddimibSMTEntry 21 }

fddimibSMTStationStatus OBJECT-TYPE
    SYNTAX  INTEGER { concatenated(1), separated(2), thru(3) }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The current status of the primary and secondary
            paths within this station."
    REFERENCE
            "ANSI { fddiSMT 45 }"
    ::= { fddimibSMTEntry 22 }

fddimibSMTPeerWrapFlag OBJECT-TYPE
    SYNTAX  INTEGER { true(1), false(2) }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "This variable assumes the value of the
            PeerWrapFlag in CFM (refer to ANSI SMT
            9.7.2.4.4)."
    REFERENCE
            "ANSI { fddiSMT 46 }"
    ::= { fddimibSMTEntry 23 }

fddimibSMTTimeStamp OBJECT-TYPE
    SYNTAX  FddiTimeMilli
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "This variable assumes the value of TimeStamp
            (refer to ANSI SMT 8.3.2.1)."
    REFERENCE
            "ANSI { fddiSMT 51 }"
    ::= { fddimibSMTEntry 24 }

fddimibSMTTransitionTimeStamp OBJECT-TYPE
    SYNTAX  FddiTimeMilli
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "This variable assumes the value of
            TransitionTimeStamp (refer to ANSI SMT 8.3.2.1)."
    REFERENCE
            "ANSI { fddiSMT 52 }"
    ::= { fddimibSMTEntry 25 }

fddimibSMTStationAction OBJECT-TYPE
    SYNTAX  INTEGER {
                other(1),               -- none of the following
                connect(2),
                disconnect(3),
                path-Test(4),
                self-Test(5),
                disable-a(6),
                disable-b(7),
                disable-m(8)
            }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
            "This object, when read, always returns a value of
            other(1).  The behavior of setting this variable
            to each of the acceptable values is as follows:

                 other(1): Results in an appropriate error.
                 connect(2): Generates a Connect signal to ECM
                      to begin a connection sequence. See ANSI
                      Ref 9.4.2.
                 disconnect(3): Generates a Disconnect signal
                      to ECM. see ANSI Ref 9.4.2.
                 path-Test(4): Initiates a station Path_Test.
                      The Path_Test variable (see ANSI Ref
                      9.4.1) is set to 'Testing'. The results
                      of this action are not specified in this
                      standard.
                 self-Test(5): Initiates a station Self_Test.
                      The results of this action are not
                      specified in this standard.
                 disable-a(6): Causes a PC_Disable on the A
                      port if the A port mode is peer.
                 disable-b(7): Causes a PC_Disable on the B
                      port if the B port mode is peer.
                 disable-m(8): Causes a PC_Disable on all M
                      ports.

            Attempts to set this object to all other values
            results in an appropriate error.  The result of
            setting this variable to path-Test(4) or self-

            Test(5) is implementation-specific."
    REFERENCE
            "ANSI { fddiSMT 60 }"
    ::= { fddimibSMTEntry 26 }

-- the MAC group
-- Implementation of the MAC Group is mandatory for all
-- systems which implement manageable FDDI subsystems.

fddimibMACNumber OBJECT-TYPE
    SYNTAX  INTEGER (0..65535)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The total number of MAC implementations (across
            all SMTs) on this network management application
            entity.  The value for this variable must remain
            constant at least from one re-initialization of
            the entity's network management system to the next
            re-initialization."
    ::= { fddimibMAC  1 }

-- the MAC table

fddimibMACTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF FddimibMACEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
            "A list of MAC entries.  The number of entries
            shall not exceed the value of fddimibMACNumber."
    ::= { fddimibMAC  2 }

fddimibMACEntry OBJECT-TYPE
    SYNTAX  FddimibMACEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
            "A MAC entry containing information common to a
            given MAC."
    INDEX   { fddimibMACSMTIndex, fddimibMACIndex }
    ::= { fddimibMACTable 1 }

FddimibMACEntry ::=
    SEQUENCE {
        fddimibMACSMTIndex

                INTEGER,
        fddimibMACIndex
                INTEGER,
        fddimibMACIfIndex
                INTEGER,
        fddimibMACFrameStatusFunctions
                INTEGER,
        fddimibMACTMaxCapability
                FddiTimeNano,
        fddimibMACTVXCapability
                FddiTimeNano,
        fddimibMACAvailablePaths
                INTEGER,
        fddimibMACCurrentPath
                INTEGER,
        fddimibMACUpstreamNbr
                FddiMACLongAddressType,
        fddimibMACDownstreamNbr
                FddiMACLongAddressType,
        fddimibMACOldUpstreamNbr
                FddiMACLongAddressType,
        fddimibMACOldDownstreamNbr
                FddiMACLongAddressType,
        fddimibMACDupAddressTest
                INTEGER,
        fddimibMACRequestedPaths
                INTEGER,
        fddimibMACDownstreamPORTType
                INTEGER,
        fddimibMACSMTAddress
                FddiMACLongAddressType,
        fddimibMACTReq
                FddiTimeNano,
        fddimibMACTNeg
                FddiTimeNano,
        fddimibMACTMax
                FddiTimeNano,
        fddimibMACTvxValue
                FddiTimeNano,
        fddimibMACFrameCts
                Counter,
        fddimibMACCopiedCts
                Counter,
        fddimibMACTransmitCts
                Counter,
        fddimibMACErrorCts
                Counter,
        fddimibMACLostCts

                Counter,
        fddimibMACFrameErrorThreshold
                INTEGER,
        fddimibMACFrameErrorRatio
                INTEGER,
        fddimibMACRMTState
                INTEGER,
        fddimibMACDaFlag
                INTEGER,
        fddimibMACUnaDaFlag
                INTEGER,
        fddimibMACFrameErrorFlag
                INTEGER,
        fddimibMACMAUnitdataAvailable
                INTEGER,
        fddimibMACHardwarePresent
                INTEGER,
        fddimibMACMAUnitdataEnable
                INTEGER
    }

fddimibMACSMTIndex OBJECT-TYPE
    SYNTAX  INTEGER (1..65535)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The value of the SMT index associated with this
            MAC."
    ::= { fddimibMACEntry 1 }

fddimibMACIndex OBJECT-TYPE
    SYNTAX  INTEGER (1..65535)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "Index variable for uniquely identifying the MAC
            object instances, which is the same as the
            corresponding resource index in SMT."
    REFERENCE
            "ANSI { fddiMAC 34 }"
    ::= { fddimibMACEntry 2 }

fddimibMACIfIndex OBJECT-TYPE
    SYNTAX  INTEGER (1..65535)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The value of the MIB-II ifIndex corresponding to
            this MAC.  If none is applicable, 0 is returned."
    REFERENCE
            "MIB-II"
    ::= { fddimibMACEntry 3 }

fddimibMACFrameStatusFunctions OBJECT-TYPE
    SYNTAX  INTEGER (0..7)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "Indicates the MAC's optional Frame Status
            processing functions.

            The value is a sum.  This value initially takes
            the value zero, then for each function present, 2
            raised to a power is added to the sum.  The powers
            are according to the following table:

                 function   Power
             fs-repeating     0
               fs-setting     1
              fs-clearing     2 "
    REFERENCE
            "ANSI { fddiMAC 11 }"
    ::= { fddimibMACEntry 4 }

fddimibMACTMaxCapability OBJECT-TYPE
    SYNTAX  FddiTimeNano
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "Indicates the maximum time value of fddiMACTMax
            that this MAC can support."
    REFERENCE
            "ANSI { fddiMAC 13 }"
    ::= { fddimibMACEntry 5 }

fddimibMACTVXCapability OBJECT-TYPE
    SYNTAX  FddiTimeNano
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "Indicates the maximum time value of
            fddiMACTvxValue that this MAC can support."
    REFERENCE
            "ANSI { fddiMAC 14 }"
    ::= { fddimibMACEntry 6 }

fddimibMACAvailablePaths OBJECT-TYPE
    SYNTAX  INTEGER (0..7)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "Indicates the paths available for this MAC (refer
            to ANSI SMT 9.7.7).

            The value is a sum.  This value initially takes
            the value zero, then for each type of PATH that
            this MAC has available, 2 raised to a power is
            added to the sum.  The powers are according to the
            following table:

                     Path   Power
                  Primary     0
                Secondary     1
                    Local     2 "
    REFERENCE
            "ANSI { fddiMAC 22 }"
    ::= { fddimibMACEntry 7 }

fddimibMACCurrentPath OBJECT-TYPE
    SYNTAX  INTEGER {
                isolated(1),
                local(2),
                secondary(3),
                primary(4),
                concatenated(5),
                thru(6)
            }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "Indicates the Path into which this MAC is
            currently inserted (refer to ANSI 9.7.7)."
    REFERENCE
            "ANSI { fddiMAC 23 }"
    ::= { fddimibMACEntry 8 }

fddimibMACUpstreamNbr OBJECT-TYPE
    SYNTAX  FddiMACLongAddressType -- OCTET STRING (SIZE (6))
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The MAC's upstream neighbor's long individual MAC
            address. It has an initial value of the SMT-
            Unknown-MAC Address and is only modified as

            specified by the Neighbor Information Frame
            protocol (refer to ANSI SMT 7.2.1 and 8.2)."
    REFERENCE
            "ANSI { fddiMAC 24 }"
    ::= { fddimibMACEntry 9 }

fddimibMACDownstreamNbr OBJECT-TYPE
    SYNTAX  FddiMACLongAddressType -- OCTET STRING (SIZE (6))
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The MAC's downstream neighbor's long individual
            MAC address. It has an initial value of the SMT-
            Unknown-MAC Address and is only modified as
            specified by the Neighbor Information Frame
            protocol (refer to ANSI SMT 7.2.1 and 8.2)."
    REFERENCE
            "ANSI { fddiMAC 25 }"
    ::= { fddimibMACEntry 10 }

fddimibMACOldUpstreamNbr OBJECT-TYPE
    SYNTAX  FddiMACLongAddressType -- OCTET STRING (SIZE (6))
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The previous value of the MAC's upstream
            neighbor's long individual MAC address. It has an
            initial value of the SMT-Unknown- MAC Address and
            is only modified as specified by the Neighbor
            Information Frame protocol (refer to ANSI SMT
            7.2.1 and 8.2)."
    REFERENCE
            "ANSI { fddiMAC 26 }"
    ::= { fddimibMACEntry 11 }

fddimibMACOldDownstreamNbr OBJECT-TYPE
    SYNTAX  FddiMACLongAddressType -- OCTET STRING (SIZE (6))
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The previous value of the MAC's downstream
            neighbor's long individual MAC address. It has an
            initial value of the SMT- Unknown-MAC Address and
            is only modified as specified by the Neighbor
            Information Frame protocol (refer to ANSI SMT
            7.2.1 and 8.2)."
    REFERENCE
            "ANSI { fddiMAC 27 }"
    ::= { fddimibMACEntry 12 }

fddimibMACDupAddressTest OBJECT-TYPE
    SYNTAX  INTEGER { none(1), pass(2), fail(3) }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The Duplicate Address Test flag, Dup_Addr_Test
            (refer to ANSI 8.2)."
    REFERENCE
            "ANSI { fddiMAC 29 }"
    ::= { fddimibMACEntry 13 }

fddimibMACRequestedPaths OBJECT-TYPE
    SYNTAX  INTEGER  (0..255)
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
            "List of permitted Paths which specifies the
            Path(s) into which the MAC may be inserted (refer
            to ansi SMT 9.7).

            The value is a sum which represents the individual
            paths that are desired.  This value initially
            takes the value zero, then for each type of PATH
            that this node is, 2 raised to a power is added to
            the sum.  The powers are according to the
            following table:

                               Path   Power
                              local     0
                secondary-alternate     1
                  primary-alternate     2
             concatenated-alternate     3
                secondary-preferred     4
                  primary-preferred     5
             concatenated-preferred     6
                               thru     7 "
    REFERENCE
            "ANSI { fddiMAC 32 }"
    ::= { fddimibMACEntry 14 }

fddimibMACDownstreamPORTType OBJECT-TYPE
    SYNTAX  INTEGER { a(1), b(2), s(3), m(4), none(5) }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "Indicates the PC-Type of the first port that is

            downstream of this MAC (the exit port)."
    REFERENCE
            "ANSI { fddiMAC 33 }"
    ::= { fddimibMACEntry 15 }

fddimibMACSMTAddress OBJECT-TYPE
    SYNTAX  FddiMACLongAddressType -- OCTET STRING (SIZE (6))
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The 48-bit individual address of the MAC used for
            SMT frames."
    REFERENCE
            "ANSI { fddiMAC 41 }"
    ::= { fddimibMACEntry 16 }

fddimibMACTReq OBJECT-TYPE
    SYNTAX  FddiTimeNano
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "This variable is the T_Req_value passed to the
            MAC.  Without having detected a duplicate, the
            time value of this variable shall assume the
            maximum supported time value which is less than or
            equal to the time value of fddiPATHMaxT-Req.  When
            a MAC has an address detected as a duplicate, it
            may use a time value for this variable greater
            than the time value of fddiPATHTMaxLowerBound.  A
            station shall cause claim when the new T_Req may
            cause the value of T_Neg to change in the claim
            process, (i.e., time value new T_Req < T_Neg, or
            old T_Req = T_Neg)."
    REFERENCE
            "ANSI { fddiMAC 51 }"
    ::= { fddimibMACEntry 17 }

fddimibMACTNeg OBJECT-TYPE
    SYNTAX  FddiTimeNano
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "It is reported as a FddiTimeNano number."
    REFERENCE
            "ANSI { fddiMAC 52 }"
    ::= { fddimibMACEntry 18 }

fddimibMACTMax OBJECT-TYPE
    SYNTAX  FddiTimeNano
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "This variable is the T_Max_value passed to the
            MAC.  The time value of this variable shall assume
            the minimum suported time value which is greater
            than or equal to the time value of fddiPATHT-
            MaxLowerBound"
    REFERENCE
            "ANSI { fddiMAC 53 }"
    ::= { fddimibMACEntry 19 }

fddimibMACTvxValue OBJECT-TYPE
    SYNTAX  FddiTimeNano
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "This variable is the TVX_value passed to the MAC.
            The time value of this variable shall assume the
            minimum suported time value which is greater than
            or equal to the time value of
            fddiPATHTVXLowerBound."
    REFERENCE
            "ANSI { fddiMAC 54 }"
    ::= { fddimibMACEntry 20 }

fddimibMACFrameCts OBJECT-TYPE
    SYNTAX  Counter
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "A count of the number of frames received by this
            MAC (refer to ANSI MAC 7.5.1)."
    REFERENCE
            "ANSI { fddiMAC 71 }"
    ::= { fddimibMACEntry 21 }

fddimibMACCopiedCts OBJECT-TYPE
    SYNTAX  Counter
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "A count that should as closely as possible match
            the number of frames addressed to (A bit set) and
            successfully copied into the station's receive
            buffers (C bit set) by this MAC (refer to ANSI MAC
            7.5). Note that this count does not include MAC

            frames."
    REFERENCE
            "ANSI { fddiMAC 72 }"
    ::= { fddimibMACEntry 22 }

fddimibMACTransmitCts OBJECT-TYPE
    SYNTAX  Counter
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "A count that should as closely as possible match
            the number of frames transmitted by this MAC
            (refer to ANSI MAC 7.5).  Note that this count
            does not include MAC frames."
    REFERENCE
            "ANSI { fddiMAC 73 }"
    ::= { fddimibMACEntry 23 }

fddimibMACErrorCts OBJECT-TYPE
    SYNTAX  Counter
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "A count of the number of frames that were
            detected in error by this MAC that had not been
            detected in error by another MAC (refer to ANSI
            MAC 7.5.2)."
    REFERENCE
            "ANSI { fddiMAC 81 }"
    ::= { fddimibMACEntry 24 }

fddimibMACLostCts OBJECT-TYPE
    SYNTAX  Counter
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "A count of the number of instances that this MAC
            detected a format error during frame reception
            such that the frame was stripped (refer to ANSI
            MAC 7.5.3)."
    REFERENCE
            "ANSI { fddiMAC 82 }"
    ::= { fddimibMACEntry 25 }

fddimibMACFrameErrorThreshold OBJECT-TYPE
    SYNTAX  INTEGER (0..65535)
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
            "A threshold for determining when a MAC Condition
            report (see ANSI 8.3.1.1) shall be generated.
            Stations not supporting variable thresholds shall
            have a value of 0 and a range of (0..0)."
    REFERENCE
            "ANSI { fddiMAC 95 }"
    ::= { fddimibMACEntry 26 }

fddimibMACFrameErrorRatio OBJECT-TYPE
    SYNTAX  INTEGER (0..65535)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "This variable is the value of the ratio,
             ((delta fddiMACLostCts + delta fddiMACErrorCts) /
             (delta fddiMACFrameCts + delta fddiMACLostCts ))
             * 2**16 "
    REFERENCE
            "ANSI { fddiMAC 96 }"
    ::= { fddimibMACEntry 27 }

fddimibMACRMTState OBJECT-TYPE
    SYNTAX  INTEGER {
                rm0(1), -- Isolated
                rm1(2), -- Non_Op
                rm2(3), -- Ring_Op
                rm3(4), -- Detect
                rm4(5), -- Non_Op_Dup
                rm5(6), -- Ring_Op_Dup
                rm6(7), -- Directed
                rm7(8)  -- Trace
            }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "Indicates the current state of the RMT State
            Machine (refer to ANSI 10.3.2)."
    REFERENCE
            "ANSI { fddiMAC 111 }"
    ::= { fddimibMACEntry 28 }

fddimibMACDaFlag OBJECT-TYPE
    SYNTAX  INTEGER { true(1), false(2) }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The RMT flag Duplicate Address Flag, DA_Flag
            (refer to ANSI 10.2.1.2)."
    REFERENCE
            "ANSI { fddiMAC 112 }"
    ::= { fddimibMACEntry 29 }

fddimibMACUnaDaFlag OBJECT-TYPE
    SYNTAX  INTEGER { true(1), false(2) }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "A flag, UNDA_Flag (refer to ANSI 8.2.2.1), set
            when the upstream neighbor reports a duplicate
            address condition. Cleared when the condition
            clears."
    REFERENCE
            "ANSI { fddiMAC 113 }"
    ::= { fddimibMACEntry 30 }

fddimibMACFrameErrorFlag OBJECT-TYPE
    SYNTAX  INTEGER { true(1), false(2) }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "Indicates the MAC Frame Error Condition is
            present when set. Cleared when the condition
            clears and on station initialization."
    REFERENCE
            "ANSI { fddiMAC 114 }"
    ::= { fddimibMACEntry 31 }

fddimibMACMAUnitdataAvailable OBJECT-TYPE
    SYNTAX  INTEGER { true(1), false(2) }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "This variable shall take on the value of the
            MAC_Avail flag defined in RMT."
    REFERENCE
            "ANSI { fddiMAC 116 }"
    ::= { fddimibMACEntry 32 }

fddimibMACHardwarePresent OBJECT-TYPE
    SYNTAX  INTEGER { true(1), false(2) }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "This variable indicates the presence of

            underlying hardware support for this MAC object.
            If the value of this object is false(2), the
            reporting of the objects in this entry may be
            handled in an implementation-specific manner."
    REFERENCE
            "ANSI { fddiMAC 117 }"
    ::= { fddimibMACEntry 33 }

fddimibMACMAUnitdataEnable OBJECT-TYPE
    SYNTAX  INTEGER { true(1), false(2) }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
            "This variable determines the value of the
            MA_UNITDATA_Enable flag in RMT.  The default and
            initial value of this flag is true(1)."
    REFERENCE
            "ANSI { fddiMAC 118 }"
    ::= { fddimibMACEntry 34 }

-- the Enhanced MAC Counters group
-- Implementation of this Group is optional, but systems
-- claiming support must implement all variables in this
-- group

-- the MAC Counters table

fddimibMACCountersTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF FddimibMACCountersEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
            "A list of MAC Counters entries.  The number of
            entries shall not exceed the value of
            fddimibMACNumber."
    ::= { fddimibMACCounters  1 }

fddimibMACCountersEntry OBJECT-TYPE
    SYNTAX  FddimibMACCountersEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
            "A MAC Counters entry containing information
            common to a given MAC."
    INDEX   { fddimibMACSMTIndex, fddimibMACIndex }
    ::= { fddimibMACCountersTable 1 }

FddimibMACCountersEntry ::=
    SEQUENCE {
        fddimibMACTokenCts
                Counter,
        fddimibMACTvxExpiredCts
                Counter,
        fddimibMACNotCopiedCts
                Counter,
        fddimibMACLateCts
                Counter,
        fddimibMACRingOpCts
                Counter,
        fddimibMACNotCopiedRatio
                INTEGER,
        fddimibMACNotCopiedFlag
                INTEGER,
        fddimibMACNotCopiedThreshold
                INTEGER
    }

fddimibMACTokenCts OBJECT-TYPE
    SYNTAX  Counter
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "A count that should as closely as possible match
            the number of times the station has received a
            token (total of non-restricted and restricted) on
            this MAC (see ANSI MAC 7.4). This count is
            valuable for determination of network load."
    REFERENCE
            "ANSI { fddiMAC 74 }"
    ::= { fddimibMACCountersEntry 1 }

fddimibMACTvxExpiredCts OBJECT-TYPE
    SYNTAX  Counter
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "A count that should as closely as possible match
            the number of times that TVX has expired."
    REFERENCE
            "ANSI { fddiMAC 83 }"
    ::= { fddimibMACCountersEntry 2 }

fddimibMACNotCopiedCts OBJECT-TYPE
    SYNTAX  Counter
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "A count that should as closely as possible match
            the number of frames that were addressed to this
            MAC but were not copied into its receive buffers
            (see ANSI MAC 7.5). For example, this might occur
            due to local buffer congestion. Because of
            implementation considerations, this count may not
            match the actual number of frames not copied. It
            is not a requirement that this count be exact.
            Note that this count does not include MAC frames."
    REFERENCE
            "ANSI { fddiMAC 84 }"
    ::= { fddimibMACCountersEntry 3 }

fddimibMACLateCts OBJECT-TYPE
    SYNTAX  Counter
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "A count that should as closely as possible match
            the number of TRT expirations since this MAC was
            reset or a token was received (refer to ANSI MAC
            7.4.5)."
    REFERENCE
            "ANSI { fddiMAC 85 }"
    ::= { fddimibMACCountersEntry 4 }

fddimibMACRingOpCts OBJECT-TYPE
    SYNTAX  Counter
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
             "The count of the number of times the ring has
            entered the 'Ring_Operational' state from the
            'Ring Not Operational' state.  This count is
            updated when a SM_MA_STATUS.Indication of a change
            in the Ring_Operational status occurs (refer to
            ANSI 6.1.4). Because of implementation
            considerations, this count may be less than the
            actual RingOp_Ct. It is not a requirement that
            this count be exact."
    REFERENCE
            "ANSI { fddiMAC 86 }"
    ::= { fddimibMACCountersEntry 5 }

fddimibMACNotCopiedRatio OBJECT-TYPE
    SYNTAX  INTEGER (0..65535)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "This variable is the value of the ratio:

             (delta fddiMACNotCopiedCts /
             (delta fddiMACCopiedCts +
               delta fddiMACNotCopiedCts )) * 2**16 "
    REFERENCE
            "ANSI { fddiMAC 105 }"
    ::= { fddimibMACCountersEntry 6 }

fddimibMACNotCopiedFlag OBJECT-TYPE
    SYNTAX  INTEGER { true(1), false(2) }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "Indicates that the Not Copied condition is
            present when read as true(1).  Set to false(2)
            when the condition clears and on station
            initialization."
    REFERENCE
            "ANSI { fddiMAC 115 }"
    ::= { fddimibMACCountersEntry 7 }

fddimibMACNotCopiedThreshold OBJECT-TYPE
    SYNTAX  INTEGER (0..65535)
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
            "A threshold for determining when a MAC condition
            report shall be generated.  Stations not
            supporting variable thresholds shall have a value
            of 0 and a range of (0..0)."
    REFERENCE
            "ANSI { fddiMAC 103 }"
    ::= { fddimibMACCountersEntry 8 }

-- the PATH group
-- Implementation of the PATH group is mandatory for all
-- systems which implement manageable FDDI subsystems.

fddimibPATHNumber OBJECT-TYPE
    SYNTAX  INTEGER (0..65535)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The total number of PATHs possible (across all
            SMTs) on this network management application
            entity.  The value for this variable must remain
            constant at least from one re-initialization of
            the entity's network management system to the next
            re-initialization."
    ::= { fddimibPATH  1 }

-- the PATH table

fddimibPATHTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF FddimibPATHEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
            "A list of PATH entries.  The number of entries
            shall not exceed the value of fddimibPATHNumber."
    ::= { fddimibPATH  2 }

fddimibPATHEntry OBJECT-TYPE
    SYNTAX  FddimibPATHEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
            "A PATH entry containing information common to a
            given PATH."
    INDEX   { fddimibPATHSMTIndex, fddimibPATHIndex }
    ::= { fddimibPATHTable 1 }

FddimibPATHEntry ::=
    SEQUENCE {
        fddimibPATHSMTIndex
                INTEGER,
        fddimibPATHIndex
                INTEGER,
        fddimibPATHTVXLowerBound
                FddiTimeNano,
        fddimibPATHTMaxLowerBound
                FddiTimeNano,
        fddimibPATHMaxTReq
                FddiTimeNano
    }

fddimibPATHSMTIndex OBJECT-TYPE
    SYNTAX  INTEGER (1..65535)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The value of the SMT index associated with this
            PATH."
    ::= { fddimibPATHEntry 1 }

fddimibPATHIndex OBJECT-TYPE
    SYNTAX  INTEGER (0..65535)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "Index variable for uniquely identifying the
            primary, secondary and local PATH object
            instances. Local PATH object instances are
            represented with integer values 3 to 255."
    REFERENCE
            "ANSI { fddiPATH 11 }"
    ::= { fddimibPATHEntry 2 }

fddimibPATHTVXLowerBound OBJECT-TYPE
    SYNTAX  FddiTimeNano
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
            "Specifies the minimum time value of
            fddiMACTvxValue that shall be used by any MAC that
            is configured in this path. The operational value
            of fddiMACTvxValue is managed by settting this
            variable.  This variable has the time value range
            of:

            0 < fddimibPATHTVXLowerBound < fddimibPATHMaxTReq
            Changes to this variable shall either satisfy the
            time value relationship:

            fddimibPATHTVXLowerBound <=
            fddimibMACTVXCapability

            of each of the MACs currently on the path, or be
            considered out of range.  The initial value of
            fddimibPATHTVXLowerBound shall be 2500 nsec (2.5
            ms)."
    REFERENCE
            "ANSI { fddiPATH 21 }"
    ::= { fddimibPATHEntry 3 }

fddimibPATHTMaxLowerBound OBJECT-TYPE
    SYNTAX  FddiTimeNano
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
            "Specifies the minimum time value of fddiMACTMax
            that shall be used by any MAC that is configured
            in this path.  The operational value of
            fddiMACTMax is managed by setting this variable.
            This variable has the time value range of:

            fddimibPATHMaxTReq <= fddimibPATHTMaxLowerBound

            and an absolute time value range of:

            10000nsec (10 msec) <= fddimibPATHTMaxLowerBound

            Changes to this variable shall either satisfy the
            time value relationship:

            fddimibPATHTMaxLowerBound <
            fddimibMACTMaxCapability

            of each of the MACs currently on the path, or be
            considered out of range.  The initial value of
            fddimibPATHTMaxLowerBound shall be 165000 nsec
            (165 msec)."
    REFERENCE
            "ANSI { fddiPATH 22 }"
    ::= { fddimibPATHEntry 4 }

fddimibPATHMaxTReq OBJECT-TYPE
    SYNTAX  FddiTimeNano
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
            "Specifies the maximum time value of fddiMACT-Req
            that shall be used by any MAC that is configured
            in this path.  The operational value of fddiMACT-
            Req is managed by setting this variable.  This
            variable has the time value range of:

            fddimibPATHTVXLowerBound < fddimibPATHMaxTReq <=
                                     fddimibPATHTMaxLowerBound.

            The default value of fddimibPATHMaxTReq is 165000
            nsec (165 msec)."
    REFERENCE
            "ANSI { fddiPATH 23 }"
    ::= { fddimibPATHEntry 5 }

-- the PATH Configuration table

fddimibPATHConfigTable OBJECT-TYPE
    SYNTAX SEQUENCE OF FddimibPATHConfigEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
            "A table of Path configuration entries.  This
            table lists all the resources that may be in this
            Path."
    REFERENCE
            "ANSI { fddiPATH 18 }"
    ::= { fddimibPATH 3 }

fddimibPATHConfigEntry OBJECT-TYPE
    SYNTAX FddimibPATHConfigEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
            "A collection of objects containing information
            for a given PATH Configuration entry."
    INDEX { fddimibPATHConfigSMTIndex,
            fddimibPATHConfigPATHIndex,
            fddimibPATHConfigTokenOrder }
    ::= { fddimibPATHConfigTable 1 }

FddimibPATHConfigEntry ::=
    SEQUENCE {
        fddimibPATHConfigSMTIndex
            INTEGER,
        fddimibPATHConfigPATHIndex
            INTEGER,
        fddimibPATHConfigTokenOrder
            INTEGER,
        fddimibPATHConfigResourceType
            INTEGER,
        fddimibPATHConfigResourceIndex
            INTEGER,
        fddimibPATHConfigCurrentPath
            INTEGER
    }

fddimibPATHConfigSMTIndex OBJECT-TYPE
    SYNTAX INTEGER (1..65535)
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
            "The value of the SMT index associated with this

            configuration entry."
    ::= { fddimibPATHConfigEntry 1 }

fddimibPATHConfigPATHIndex OBJECT-TYPE
    SYNTAX INTEGER (1..65535)
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
            "The value of the PATH resource index associated
            with this configuration entry."
    ::= { fddimibPATHConfigEntry 2 }

fddimibPATHConfigTokenOrder OBJECT-TYPE
    SYNTAX INTEGER (1..65535)
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
            "An object associated with Token order for this
            entry.  Thus if the token passes resources a, b, c
            and d, in that order, then the value of this
            object for these resources would be 1, 2, 3 and 4
            respectively."
    ::= { fddimibPATHConfigEntry 3 }

fddimibPATHConfigResourceType OBJECT-TYPE
    SYNTAX INTEGER { mac(2), port(4) }
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
            "The type of resource associated with this
            configuration entry."
    ::= { fddimibPATHConfigEntry 4 }

fddimibPATHConfigResourceIndex OBJECT-TYPE
    SYNTAX INTEGER (1..65535)
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
            "The value of the SMT resource index used to refer
            to the instance of this MAC or Port resource."
    ::= { fddimibPATHConfigEntry 5 }

fddimibPATHConfigCurrentPath OBJECT-TYPE
    SYNTAX INTEGER {
             isolated(1), local(2), secondary(3), primary(4),
             concatenated(5), thru(6)
           }
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
            "The current insertion status for this resource on
            this Path."
    ::= { fddimibPATHConfigEntry 6 }

-- the PORT group
-- Implementation of the PORT group is mandatory for all
-- systems which implement manageable FDDI subsystems.

fddimibPORTNumber OBJECT-TYPE
    SYNTAX  INTEGER (0..65535)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The total number of PORT implementations (across
            all SMTs) on this network management application
            entity.  The value for this variable must remain
            constant at least from one re-initialization of
            the entity's network management system to the next
            re-initialization."
    ::= { fddimibPORT  1 }

-- the PORT table

fddimibPORTTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF FddimibPORTEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
            "A list of PORT entries.  The number of entries
            shall not exceed the value of fddimibPORTNumber."
    ::= { fddimibPORT  2 }

fddimibPORTEntry OBJECT-TYPE
    SYNTAX  FddimibPORTEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
            "A PORT entry containing information common to a
            given PORT."
    INDEX   { fddimibPORTSMTIndex, fddimibPORTIndex }
    ::= { fddimibPORTTable 1 }

FddimibPORTEntry ::=
    SEQUENCE {

        fddimibPORTSMTIndex
                INTEGER,
        fddimibPORTIndex
                INTEGER,
        fddimibPORTMyType
                INTEGER,
        fddimibPORTNeighborType
                INTEGER,
        fddimibPORTConnectionPolicies
                INTEGER,
        fddimibPORTMACIndicated
                INTEGER,
        fddimibPORTCurrentPath
                INTEGER,
        fddimibPORTRequestedPaths
                OCTET STRING,
        fddimibPORTMACPlacement
                FddiResourceId,
        fddimibPORTAvailablePaths
                INTEGER,
        fddimibPORTPMDClass
                INTEGER,
        fddimibPORTConnectionCapabilities
                INTEGER,
        fddimibPORTBSFlag
                INTEGER,
        fddimibPORTLCTFailCts
                Counter,
        fddimibPORTLerEstimate
                INTEGER,
        fddimibPORTLemRejectCts
                Counter,
        fddimibPORTLemCts
                Counter,
        fddimibPORTLerCutoff
                INTEGER,
        fddimibPORTLerAlarm
                INTEGER,
        fddimibPORTConnectState
                INTEGER,
        fddimibPORTPCMState
                INTEGER,
        fddimibPORTPCWithhold
                INTEGER,
        fddimibPORTLerFlag
                INTEGER,
        fddimibPORTHardwarePresent
                INTEGER,
        fddimibPORTAction
                INTEGER
    }

fddimibPORTSMTIndex OBJECT-TYPE
    SYNTAX  INTEGER (1..65535)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The value of the SMT index associated with this
            PORT."
    ::= { fddimibPORTEntry 1 }

fddimibPORTIndex OBJECT-TYPE
    SYNTAX  INTEGER (1..65535)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "A unique value for each PORT within a given SMT,
            which is the same as the corresponding resource
            index in SMT.  The value for each PORT must remain
            constant at least from one re-initialization of
            the entity's network management system to the next
            re-initialization."
    REFERENCE
            "ANSI { fddiPORT 29 }"
    ::= { fddimibPORTEntry 2 }

fddimibPORTMyType OBJECT-TYPE
    SYNTAX  INTEGER { a(1), b(2), s(3), m(4), none(5) }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The value of the PORT's PC_Type (refer to ANSI
            9.4.1, and 9.6.3.2)."
    REFERENCE
            "ANSI { fddiPORT 12 }"
    ::= { fddimibPORTEntry 3 }

fddimibPORTNeighborType OBJECT-TYPE
    SYNTAX  INTEGER { a(1), b(2), s(3), m(4), none(5) }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The type of the remote PORT as determined in PCM.
            This variable has an initial value of none, and is
            only modified in PC_RCode(3)_Actions (refer to
            ANSI SMT 9.6.3.2)."
    REFERENCE
            "ANSI { fddiPORT 13 }"
    ::= { fddimibPORTEntry 4 }

fddimibPORTConnectionPolicies OBJECT-TYPE
    SYNTAX  INTEGER (0..3)
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
            "A value representing the PORT's connection
            policies desired in the node. The value of pc-
            mac-lct is a term used in the PC_MAC_LCT Flag (see
            9.4.3.2).  The value of pc-mac-loop is a term used
            in the PC_MAC_Loop Flag.

            The value is a sum.  This value initially takes
            the value zero, then for each PORT policy, 2
            raised to a power is added to the sum.  The powers
            are according to the following table:

                          Policy   Power
                      pc-mac-lct     0
                     pc-mac-loop     1 "
    REFERENCE
            "ANSI { fddiPORT 14 }"
    ::= { fddimibPORTEntry 5 }

fddimibPORTMACIndicated OBJECT-TYPE
    SYNTAX  INTEGER {
                tVal9FalseRVal9False(1),
                tVal9FalseRVal9True(2),
                tVal9TrueRVal9False(3),
                tVal9TrueRVal9True(4)
            }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The indications (T_Val(9), R_Val(9)) in PC-
            Signalling, of the intent to place a MAC in the
            output token path to a PORT (refer to ANSI SMT
            9.6.3.2.)."
    REFERENCE
            "ANSI { fddiPORT 15 }"
    ::= { fddimibPORTEntry 6 }

fddimibPORTCurrentPath OBJECT-TYPE
    SYNTAX  INTEGER {
                ce0(1), -- isolated

                ce1(2), -- local
                ce2(3), -- secondary
                ce3(4), -- primary
                ce4(5), -- concatenated
                ce5(6)  -- thru
            }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "Indicates the Path(s) into which this PORT is
            currently inserted."
    REFERENCE
            "ANSI { fddiPORT 16 }"
    ::= { fddimibPORTEntry 7 }

fddimibPORTRequestedPaths OBJECT-TYPE
    SYNTAX  OCTET STRING (SIZE (3))
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
            "This variable is a list of permitted Paths where
            each list element defines the Port's permitted
            Paths.  The first octet corresponds to 'none', the
            second octet to 'tree', and the third octet to
            'peer'."
    REFERENCE
            "ANSI { fddiPORT 17 }"
    ::= { fddimibPORTEntry 8 }

fddimibPORTMACPlacement OBJECT-TYPE
    SYNTAX  FddiResourceId -- INTEGER (0..65535)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "Indicates the MAC, if any, whose transmit path
            exits the station via this PORT. The value shall
            be zero if there is no MAC associated with the
            PORT. Otherwise, the MACIndex of the MAC will be
            the value of the variable."
    REFERENCE
            "ANSI { fddiPORT 18 }"
    ::= { fddimibPORTEntry 9 }

fddimibPORTAvailablePaths OBJECT-TYPE
    SYNTAX  INTEGER (0..7)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "Indicates the Paths which are available to this
            Port. In the absence of faults, the A and B Ports
            will always have both the Primary and Secondary
            Paths available.

            The value is a sum.  This value initially takes
            the value zero, then for each type of PATH that
            this port has available, 2 raised to a power is
            added to the sum.  The powers are according to the
            following table:

                     Path   Power
                  Primary     0
                Secondary     1
                    Local     2 "
    REFERENCE
            "ANSI { fddiPORT 19 }"
    ::= { fddimibPORTEntry 10 }

fddimibPORTPMDClass OBJECT-TYPE
    SYNTAX  INTEGER {
                    multimode(1),
                    single-mode1(2),
                    single-mode2(3),
                    sonet(4),
                    low-cost-fiber(5),
                    twisted-pair(6),
                    unknown(7),
                    unspecified(8)
            }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "This variable indicates the type of PMD entity
            associated with this port."
    REFERENCE
            "ANSI { fddiPORT 22 }"
    ::= { fddimibPORTEntry 11 }

fddimibPORTConnectionCapabilities OBJECT-TYPE
    SYNTAX  INTEGER (0..3)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "A value that indicates the connection
            capabilities of the port. The pc-mac-lct bit
            indicates that the station has the capability of
            setting the PC_MAC_LCT Flag. The pc-mac-loop bit

            indicates that the station has the capability of
            setting the PC_MAC_Loop Flag (refer to ANSI
            9.4.3.2).

            The value is a sum.  This value initially takes
            the value zero, then for each capability that this
            port has, 2 raised to a power is added to the sum.
            The powers are according to the following table:

               capability   Power
               pc-mac-lct     0
              pc-mac-loop     1 "
    REFERENCE
            "ANSI { fddiPORT 23 }"
    ::= { fddimibPORTEntry 12 }

fddimibPORTBSFlag OBJECT-TYPE
    SYNTAX  INTEGER { true(1), false(2) }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "This variable assumes the value of the BS_Flag
            (refer to ANSI SMT 9.4.3.3)."
    REFERENCE
            "ANSI { fddiPORT 33 }"
    ::= { fddimibPORTEntry 13 }

fddimibPORTLCTFailCts OBJECT-TYPE
    SYNTAX  Counter
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The count of the consecutive times the link
            confidence test (LCT) has failed during connection
            management (refer to ANSI 9.4.1)."
    REFERENCE
            "ANSI { fddiPORT 42 }"
    ::= { fddimibPORTEntry 14 }

fddimibPORTLerEstimate OBJECT-TYPE
    SYNTAX  INTEGER (4..15)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "A long term average link error rate. It ranges
            from 10**-4 to 10**-15 and is reported as the
            absolute value of the base 10 logarithm (refer to
            ANSI SMT 9.4.7.5.)."
    REFERENCE
            "ANSI { fddiPORT 51 }"
    ::= { fddimibPORTEntry 15 }

fddimibPORTLemRejectCts OBJECT-TYPE
    SYNTAX  Counter
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "A link error monitoring count of the times that a
            link has been rejected."
    REFERENCE
            "ANSI { fddiPORT 52 }"
    ::= { fddimibPORTEntry 16 }

fddimibPORTLemCts OBJECT-TYPE
    SYNTAX  Counter
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The aggregate link error monitor error count, set
            to zero only on station initialization."
    REFERENCE
            "ANSI { fddiPORT 53 }"
    ::= { fddimibPORTEntry 17 }

fddimibPORTLerCutoff OBJECT-TYPE
    SYNTAX  INTEGER (4..15)
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
             "The link error rate estimate at which a link
            connection will be broken. It ranges from 10**-4
            to 10**-15 and is reported as the absolute value
            of the base 10 logarithm (default of 7)."
    REFERENCE
            "ANSI { fddiPORT 58 }"
    ::= { fddimibPORTEntry 18 }

fddimibPORTLerAlarm OBJECT-TYPE
    SYNTAX  INTEGER (4..15)
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
            "The link error rate estimate at which a link
            connection will generate an alarm. It ranges from
            10**-4 to 10**-15 and is reported as the absolute
            value of the base 10 logarithm of the estimate

            (default of 8)."
    REFERENCE
            "ANSI { fddiPORT 59 }"
    ::= { fddimibPORTEntry 19 }

fddimibPORTConnectState OBJECT-TYPE
    SYNTAX  INTEGER {
                disabled(1),
                connecting(2),
                standby(3),
                active(4)
            }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "An indication of the connect state of this PORT
            and is equal to the value of Connect_State (refer
            to ANSI 9.4.1)"
    REFERENCE
            "ANSI { fddiPORT 61 }"
    ::= { fddimibPORTEntry 20 }

fddimibPORTPCMState OBJECT-TYPE
    SYNTAX  INTEGER {
                pc0(1), -- Off
                pc1(2), -- Break
                pc2(3), -- Trace
                pc3(4), -- Connect
                pc4(5), -- Next
                pc5(6), -- Signal
                pc6(7), -- Join
                pc7(8), -- Verify
                pc8(9), -- Active
                pc9(10) -- Maint
            }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The state of this Port's PCM state machine refer
            to ANSI SMT 9.6.2)."
    REFERENCE
            "ANSI { fddiPORT 62 }"
    ::= { fddimibPORTEntry 21 }

fddimibPORTPCWithhold OBJECT-TYPE
    SYNTAX  INTEGER {
                 none(1),
                 m-m(2),
                 otherincompatible(3),
                 pathnotavailable(4)
            }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The value of PC_Withhold (refer to ANSI SMT
            9.4.1)."
    REFERENCE
            "ANSI { fddiPORT 63 }"
    ::= { fddimibPORTEntry 22 }

fddimibPORTLerFlag OBJECT-TYPE
    SYNTAX  INTEGER { true(1), false(2) }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "The condition becomes active when the value of
            fddiPORTLerEstimate is less than or equal to
            fddiPORTLerAlarm. This will be reported with the
            Status Report Frames (SRF) (refer to ANSI SMT
             7.2.7 and 8.3)."
    REFERENCE
            "ANSI { fddiPORT 64 }"
    ::= { fddimibPORTEntry 23 }

fddimibPORTHardwarePresent OBJECT-TYPE
    SYNTAX  INTEGER { true(1), false(2) }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
            "This variable indicates the presence of
            underlying hardware support for this Port object.
            If the value of this object is false(2), the
            reporting of the objects in this entry may be
            handled in an implementation-specific manner."
    REFERENCE
            "ANSI { fddiPORT 65 }"
    ::= { fddimibPORTEntry 24 }

fddimibPORTAction OBJECT-TYPE
    SYNTAX  INTEGER {
            other(1),           -- none of the following
            maintPORT(2),
            enablePORT(3),
            disablePORT(4),
            startPORT(5),
            stopPORT(6)

            }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
            "Causes a Control signal to be generated with a
            control_action of 'Signal' and the 'variable'
            parameter set with the appropriate value (i.e.,
            PC_Maint, PC_Enable, PC_Disable, PC_Start, or
            PC_Stop) (refer to ANSI 9.4.2)."
    REFERENCE
            "ANSI { fddiPORT 70 }"
    ::= { fddimibPORTEntry 25 }

END