Peler

: / usr / share / snmp / mibs / ietf /
Filename : DOCS-IETF-BPI2-MIB
back
DOCS-IETF-BPI2-MIB DEFINITIONS ::= BEGIN

IMPORTS
        MODULE-IDENTITY, OBJECT-TYPE,
        Integer32,
        Unsigned32,
        Counter32,
        mib-2
             FROM SNMPv2-SMI           -- [RFC2578]
        SnmpAdminString
             FROM SNMP-FRAMEWORK-MIB   -- [RFC3411]
        TEXTUAL-CONVENTION,
        MacAddress,
        RowStatus,
        TruthValue,
        DateAndTime,
        StorageType
             FROM SNMPv2-TC            -- [RFC2579]
        OBJECT-GROUP,
        MODULE-COMPLIANCE
             FROM SNMPv2-CONF          -- [RFC2580]
        ifIndex
             FROM IF-MIB               -- [RFC2863]
        InetAddressType,
        InetAddress

             FROM INET-ADDRESS-MIB;    -- [RFC4001]

   docsBpi2MIB    MODULE-IDENTITY
        LAST-UPDATED "200507200000Z" -- July 20, 2005
        ORGANIZATION "IETF IP over Cable Data Network (IPCDN)
                      Working Group"
        CONTACT-INFO "---------------------------------------
                   Stuart M. Green
                   E-mail: rubbersoul3@yahoo.com
                   ---------------------------------------
                   Kaz Ozawa
                   Automotive Systems Development Center
                   TOSHIBA CORPORATION
                   1-1, Shibaura 1-Chome
                   Minato-ku, Tokyo 105-8001
                   Japan
                   Phone: +81-3-3457-8569
                   Fax: +81-3-5444-9325
                   E-mail: Kazuyoshi.Ozawa@toshiba.co.jp
                   ---------------------------------------
                   Alexander Katsnelson
                   Postal:
                   Tel:    +1-303-680-3924
                   E-mail: katsnelson6@peoplepc.com
                   ---------------------------------------
                   Eduardo Cardona
                   Postal:
                   Cable Television Laboratories, Inc.
                   858 Coal Creek Circle
                   Louisville, CO 80027- 9750
                   U.S.A.
                   Tel:    +1 303 661 9100
                   Fax:    +1 303 661 9199
                   E-mail: e.cardona@cablelabs.com
                   ---------------------------------------

           IETF IPCDN Working Group
           General Discussion: ipcdn@ietf.org
           Subscribe: http://www.ietf.org/mailman/listinfo/ipcdn.
           Archive: ftp://ftp.ietf.org/ietf-mail-archive/ipcdn.
           Co-chairs: Richard Woundy, rwoundy@cisco.com
                      Jean-Francois Mule, jfm@cablelabs.com"
        DESCRIPTION
            "This is the MIB module for the DOCSIS Baseline
             Privacy Plus Interface (BPI+) at cable modems (CMs)
             and cable modem termination systems (CMTSs).

             Copyright (C) The Internet Society (2005).  This

             version of this MIB module is part of RFC 4131; see
             the RFC itself for full legal notices."

        REVISION        "200507200000Z"  -- July 20, 2005
        DESCRIPTION
            "Initial version of the IETF BPI+ MIB module.
             This version published as RFC 4131."
           ::= { mib-2 126 }

   -- Textual conventions

DocsX509ASN1DEREncodedCertificate ::= TEXTUAL-CONVENTION
        STATUS    current
        DESCRIPTION
            "An X509 digital certificate encoded as an ASN.1 DER
        object."
        SYNTAX    OCTET STRING (SIZE (0..4096))

DocsSAId ::= TEXTUAL-CONVENTION
        DISPLAY-HINT "d"
        STATUS    current
        DESCRIPTION
             "Security Association identifier (SAID)."
        REFERENCE
              "DOCSIS Baseline Privacy Plus Interface
        specification, Section 2.1.3, BPI+ Security
        Associations"
        SYNTAX    Integer32 (1..16383)

DocsSAIdOrZero ::= TEXTUAL-CONVENTION
        DISPLAY-HINT "d"
        STATUS    current
        DESCRIPTION
             "Security Association identifier (SAID).  The value
        zero indicates that the SAID is yet to be determined."
        REFERENCE
              "DOCSIS Baseline Privacy Plus Interface
        specification, Section 2.1.3, BPI+ Security
              Associations"
        SYNTAX    Unsigned32 (0 | 1..16383)

DocsBpkmSAType ::= TEXTUAL-CONVENTION
        STATUS    current
        DESCRIPTION
             "The type of security association (SA).
        The values of the named-numbers are associated
        with the BPKM SA-Type attributes:
        'primary' corresponds to code '1', 'static' to code '2',
        and 'dynamic' to code '3'.
        The 'none' value must only be used if the SA type has yet
        to be determined."
        REFERENCE
              "DOCSIS Baseline Privacy Plus Interface
        specification, Section 4.2.2.24"
        SYNTAX    INTEGER {
                       none(0),
                       primary(1),
                       static(2),
                       dynamic(3)
                  }

DocsBpkmDataEncryptAlg ::= TEXTUAL-CONVENTION
        STATUS    current
        DESCRIPTION
            "The list of data encryption algorithms defined for
        the DOCSIS interface in the BPKM cryptographic-suite
        parameter.  The value 'none' indicates that the SAID
        being referenced has no data encryption."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.2.20."
        SYNTAX    INTEGER {
                       none(0),
                       des56CbcMode(1),
                       des40CbcMode(2),
                       t3Des128CbcMode(3),
                       aes128CbcMode(4),
                       aes256CbcMode(5)
                  }

DocsBpkmDataAuthentAlg ::= TEXTUAL-CONVENTION
        STATUS    current
        DESCRIPTION
            "The list of data integrity algorithms defined for the
        DOCSIS interface in the BPKM cryptographic-suite parameter.
        The value 'none' indicates that no data integrity is used for
        the SAID being referenced."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.2.20."
        SYNTAX    INTEGER {
                       none(0),
                       hmacSha196(1)
                  }

   docsBpi2MIBObjects  OBJECT IDENTIFIER ::= { docsBpi2MIB 1 }

   -- Cable Modem Group

   docsBpi2CmObjects OBJECT IDENTIFIER ::= { docsBpi2MIBObjects 1 }

   --
   -- The BPI+ base and authorization table for CMs,
   -- indexed by ifIndex
   --

   docsBpi2CmBaseTable OBJECT-TYPE
        SYNTAX              SEQUENCE OF    DocsBpi2CmBaseEntry
        MAX-ACCESS          not-accessible
        STATUS              current
        DESCRIPTION
             "This table describes the basic and authorization-
        related Baseline Privacy Plus attributes of each CM MAC
        interface."
        ::= { docsBpi2CmObjects 1 }

   docsBpi2CmBaseEntry OBJECT-TYPE
        SYNTAX              DocsBpi2CmBaseEntry
        MAX-ACCESS          not-accessible
        STATUS              current
        DESCRIPTION
             "Each entry contains objects describing attributes of
        one CM MAC interface.  An entry in this table exists for
        each ifEntry with an ifType of docsCableMaclayer(127)."
        INDEX               { ifIndex }
        ::= { docsBpi2CmBaseTable 1 }

   DocsBpi2CmBaseEntry ::= SEQUENCE {
        docsBpi2CmPrivacyEnable             TruthValue,
        docsBpi2CmPublicKey                 OCTET STRING,
        docsBpi2CmAuthState                 INTEGER,
        docsBpi2CmAuthKeySequenceNumber     Integer32,
        docsBpi2CmAuthExpiresOld            DateAndTime,
        docsBpi2CmAuthExpiresNew            DateAndTime,
        docsBpi2CmAuthReset                 TruthValue,
        docsBpi2CmAuthGraceTime             Integer32,
        docsBpi2CmTEKGraceTime              Integer32,
        docsBpi2CmAuthWaitTimeout           Integer32,
        docsBpi2CmReauthWaitTimeout         Integer32,
        docsBpi2CmOpWaitTimeout             Integer32,
        docsBpi2CmRekeyWaitTimeout          Integer32,
        docsBpi2CmAuthRejectWaitTimeout     Integer32,
        docsBpi2CmSAMapWaitTimeout          Integer32,
        docsBpi2CmSAMapMaxRetries           Integer32,
        docsBpi2CmAuthentInfos              Counter32,
        docsBpi2CmAuthRequests              Counter32,
        docsBpi2CmAuthReplies               Counter32,
        docsBpi2CmAuthRejects               Counter32,
        docsBpi2CmAuthInvalids              Counter32,
        docsBpi2CmAuthRejectErrorCode       INTEGER,
        docsBpi2CmAuthRejectErrorString     SnmpAdminString,
        docsBpi2CmAuthInvalidErrorCode      INTEGER,
        docsBpi2CmAuthInvalidErrorString    SnmpAdminString
        }

   docsBpi2CmPrivacyEnable  OBJECT-TYPE
        SYNTAX              TruthValue
        MAX-ACCESS          read-only
        STATUS              current
        DESCRIPTION
             "This object identifies whether this CM is
        provisioned to run Baseline Privacy Plus."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Appendix A.1.1."
        ::= { docsBpi2CmBaseEntry 1 }

   docsBpi2CmPublicKey     OBJECT-TYPE
        SYNTAX             OCTET STRING (SIZE (0..524))
        MAX-ACCESS         read-only
        STATUS             current
        DESCRIPTION
             "The value of this object is a DER-encoded
        RSAPublicKey ASN.1 type string, as defined in the RSA
        Encryption Standard (PKCS #1), corresponding to the
        public key of the CM."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.2.4."
        ::= { docsBpi2CmBaseEntry 2 }

   docsBpi2CmAuthState OBJECT-TYPE
        SYNTAX         INTEGER   {
                       start(1),
                       authWait(2),
                       authorized(3),
                       reauthWait(4),
                       authRejectWait(5),
                       silent(6)
                  }
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the state of the CM
        authorization FSM.  The start state indicates that FSM is
        in its initial state."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.1.2.1."
        ::= { docsBpi2CmBaseEntry 3 }

   docsBpi2CmAuthKeySequenceNumber    OBJECT-TYPE
        SYNTAX              Integer32 (0..15)
        MAX-ACCESS          read-only
        STATUS              current
        DESCRIPTION
             "The value of this object is the most recent
        authorization key sequence number for this FSM."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.1.2 and 4.2.2.10."
        ::= { docsBpi2CmBaseEntry 4 }

   docsBpi2CmAuthExpiresOld OBJECT-TYPE
        SYNTAX              DateAndTime
        MAX-ACCESS          read-only
        STATUS              current
        DESCRIPTION
             "The value of this object is the actual clock time for
        expiration of the immediate predecessor of the most recent
        authorization key for this FSM.  If this FSM has only one
        authorization key, then the value is the time of activation
        of this FSM."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.1.2 and 4.2.2.9."
        ::= { docsBpi2CmBaseEntry 5 }

   docsBpi2CmAuthExpiresNew OBJECT-TYPE
        SYNTAX              DateAndTime
        MAX-ACCESS          read-only
        STATUS              current
        DESCRIPTION
             "The value of this object is the actual clock time for
        expiration of the most recent authorization key for this
        FSM."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.1.2 and 4.2.2.9."
        ::= { docsBpi2CmBaseEntry 6 }

   docsBpi2CmAuthReset OBJECT-TYPE
        SYNTAX         TruthValue
        MAX-ACCESS     read-write
        STATUS         current
        DESCRIPTION
             "Setting this object to 'true' generates a Reauthorize
        event in the authorization FSM.  Reading this object always
        returns FALSE.

        This object is for testing purposes only, and therefore it
        is not required to be associated with a last reset
        object."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.1.2.3.4."
        ::= { docsBpi2CmBaseEntry 7 }

   docsBpi2CmAuthGraceTime  OBJECT-TYPE
        SYNTAX         Integer32 (1..6047999)
        UNITS          "seconds"
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the grace time for an
        authorization key in seconds.  A CM is expected to start
        trying to get a new authorization key beginning
        AuthGraceTime seconds before the most recent authorization
        key actually expires."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Appendix A.1.1.1.3."
        ::= { docsBpi2CmBaseEntry 8 }

   docsBpi2CmTEKGraceTime   OBJECT-TYPE
        SYNTAX         Integer32 (1..302399)
        UNITS          "seconds"
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the grace time for
        the TEK in seconds.  The CM is expected to start trying to
        acquire a new TEK beginning TEK GraceTime seconds before
        the expiration of the most recent TEK."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Appendix A.1.1.1.6."
        ::= { docsBpi2CmBaseEntry 9 }

   docsBpi2CmAuthWaitTimeout     OBJECT-TYPE
        SYNTAX         Integer32 (1..30)
        UNITS          "seconds"
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the Authorize Wait
        Timeout in seconds."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Appendix A.1.1.1.1."
        ::= { docsBpi2CmBaseEntry 10 }

   docsBpi2CmReauthWaitTimeout   OBJECT-TYPE
        SYNTAX         Integer32 (1..30)
        UNITS          "seconds"
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the Reauthorize Wait
        Timeout in seconds."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Appendix A.1.1.1.2."
        ::= { docsBpi2CmBaseEntry 11 }

   docsBpi2CmOpWaitTimeout  OBJECT-TYPE
        SYNTAX         Integer32 (1..10)
        UNITS          "seconds"
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the Operational Wait
        Timeout in seconds."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Appendix A.1.1.1.4."
        ::= { docsBpi2CmBaseEntry 12 }

   docsBpi2CmRekeyWaitTimeout    OBJECT-TYPE
        SYNTAX         Integer32 (1..10)
        UNITS          "seconds"
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the Rekey Wait Timeout
        in seconds."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Appendix A.1.1.1.5."
        ::= { docsBpi2CmBaseEntry 13 }

   docsBpi2CmAuthRejectWaitTimeout    OBJECT-TYPE
        SYNTAX         Integer32 (1..600)
        UNITS          "seconds"
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the Authorization Reject
        Wait Timeout in seconds."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Appendix A.1.1.1.7."
        ::= { docsBpi2CmBaseEntry 14 }

   docsBpi2CmSAMapWaitTimeout    OBJECT-TYPE
        SYNTAX         Integer32 (1..10)
        UNITS          "seconds"
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the retransmission
        interval, in seconds, of SA Map Requests from the MAP Wait
        state."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Appendix A.1.1.1.8."
        ::= { docsBpi2CmBaseEntry 15 }

   docsBpi2CmSAMapMaxRetries     OBJECT-TYPE
        SYNTAX         Integer32 (0..10)
        UNITS          "count"
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the maximum number of
        Map Request retries allowed."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Appendix A.1.1.1.9."
        ::= { docsBpi2CmBaseEntry 16 }

   docsBpi2CmAuthentInfos   OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the number of times
        the CM has transmitted an Authentication Information
        message.  Discontinuities in the value of this counter can
        occur at re-initialization of the management system, and at
        other times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.9."
        ::= { docsBpi2CmBaseEntry 17 }

   docsBpi2CmAuthRequests   OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the number of times the CM
        has transmitted an Authorization Request message.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.1."
        ::= { docsBpi2CmBaseEntry 18 }

   docsBpi2CmAuthReplies    OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the number of times the CM
        has received an Authorization Reply message.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.2."
        ::= { docsBpi2CmBaseEntry 19 }

   docsBpi2CmAuthRejects    OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the number of times the CM
        has received an Authorization Reject message.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.3."
        ::= { docsBpi2CmBaseEntry 20 }

   docsBpi2CmAuthInvalids   OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the count of times the CM
        has received an Authorization Invalid message.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.7."
        ::= { docsBpi2CmBaseEntry 21 }

   docsBpi2CmAuthRejectErrorCode OBJECT-TYPE
        SYNTAX         INTEGER {
                              none(1),
                              unknown(2),
                              unauthorizedCm(3),
                              unauthorizedSaid(4),
                              permanentAuthorizationFailure(8),
                              timeOfDayNotAcquired(11)
                              }
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the enumerated
        description of the Error-Code in the most recent
        Authorization Reject message received by the CM.  This has
        the value unknown(2) if the last Error-Code value was 0 and
        none(1) if no Authorization Reject message has been received
        since reboot."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.1.3 and 4.2.2.15."
        ::= { docsBpi2CmBaseEntry 22 }

   docsBpi2CmAuthRejectErrorString    OBJECT-TYPE
        SYNTAX         SnmpAdminString (SIZE (0..128))
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the text string in the
        most recent Authorization Reject message received by the
        CM.  This is a zero length string if no Authorization
        Reject message has been received since reboot."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.1.3 and 4.2.2.6."
        ::= { docsBpi2CmBaseEntry 23 }

   docsBpi2CmAuthInvalidErrorCode     OBJECT-TYPE
        SYNTAX         INTEGER {
                              none(1),
                              unknown(2),
                              unauthorizedCm(3),
                              unsolicited(5),
                              invalidKeySequence(6),
                              keyRequestAuthenticationFailure(7)
                              }
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the enumerated
        description of the Error-Code in the most recent
        Authorization Invalid message received by the CM.  This has
        the value unknown(2) if the last Error-Code value was 0 and
        none(1) if no Authorization Invalid message has been received
        since reboot."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.1.7 and 4.2.2.15."
        ::= { docsBpi2CmBaseEntry 24 }

   docsBpi2CmAuthInvalidErrorString   OBJECT-TYPE
        SYNTAX         SnmpAdminString (SIZE (0..128))
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the text string in the
        most recent Authorization Invalid message received by the
        CM.  This is a zero length string if no Authorization

        Invalid message has been received since reboot."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.1.7 and 4.2.2.6."
        ::= { docsBpi2CmBaseEntry 25 }

   --
   -- The CM TEK Table, indexed by ifIndex and SAID
   --

   docsBpi2CmTEKTable  OBJECT-TYPE
        SYNTAX         SEQUENCE OF    DocsBpi2CmTEKEntry
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
             "This table describes the attributes of each CM
        Traffic Encryption Key (TEK) association.  The CM maintains
        (no more than) one TEK association per SAID per CM MAC
        interface."
        ::= { docsBpi2CmObjects 2 }

   docsBpi2CmTEKEntry  OBJECT-TYPE
        SYNTAX         DocsBpi2CmTEKEntry
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
             "Each entry contains objects describing the TEK
        association attributes of one SAID.  The CM MUST create one
        entry per SAID, regardless of whether the SAID was obtained
        from a Registration Response message, from an Authorization
        Reply message, or from any dynamic SAID establishment
        mechanisms."
        INDEX     { ifIndex, docsBpi2CmTEKSAId }
        ::= { docsBpi2CmTEKTable 1 }

   DocsBpi2CmTEKEntry ::= SEQUENCE {
        docsBpi2CmTEKSAId                  DocsSAId,
        docsBpi2CmTEKSAType                DocsBpkmSAType,
        docsBpi2CmTEKDataEncryptAlg        DocsBpkmDataEncryptAlg,
        docsBpi2CmTEKDataAuthentAlg        DocsBpkmDataAuthentAlg,
        docsBpi2CmTEKState                 INTEGER,
        docsBpi2CmTEKKeySequenceNumber     Integer32,
        docsBpi2CmTEKExpiresOld            DateAndTime,
        docsBpi2CmTEKExpiresNew            DateAndTime,
        docsBpi2CmTEKKeyRequests           Counter32,
        docsBpi2CmTEKKeyReplies            Counter32,
        docsBpi2CmTEKKeyRejects            Counter32,
        docsBpi2CmTEKInvalids              Counter32,
        docsBpi2CmTEKAuthPends             Counter32,
        docsBpi2CmTEKKeyRejectErrorCode    INTEGER,
        docsBpi2CmTEKKeyRejectErrorString  SnmpAdminString,
        docsBpi2CmTEKInvalidErrorCode      INTEGER,
        docsBpi2CmTEKInvalidErrorString    SnmpAdminString
        }

   docsBpi2CmTEKSAId   OBJECT-TYPE
        SYNTAX         DocsSAId
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
             "The value of this object is the DOCSIS Security
        Association ID (SAID)."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.2.12."
        ::= { docsBpi2CmTEKEntry 1 }

   docsBpi2CmTEKSAType OBJECT-TYPE
        SYNTAX         DocsBpkmSAType
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the type of security
        association."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 2.1.3."
        ::= { docsBpi2CmTEKEntry 2 }

   docsBpi2CmTEKDataEncryptAlg   OBJECT-TYPE
        SYNTAX    DocsBpkmDataEncryptAlg
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the data encryption
        algorithm for this SAID."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.2.20."
        ::= { docsBpi2CmTEKEntry 3 }

   docsBpi2CmTEKDataAuthentAlg   OBJECT-TYPE
        SYNTAX    DocsBpkmDataAuthentAlg
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the data authentication
        algorithm for this SAID."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.2.20."
        ::= { docsBpi2CmTEKEntry 4 }

   docsBpi2CmTEKState  OBJECT-TYPE
        SYNTAX         INTEGER {
                               start(1),
                               opWait(2),
                               opReauthWait(3),
                               operational(4),
                               rekeyWait(5),
                               rekeyReauthWait(6)
                               }
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the state of the
        indicated TEK FSM.  The start(1) state indicates that the
        FSM is in its initial state."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.1.3.1."
        ::= { docsBpi2CmTEKEntry 5 }

   docsBpi2CmTEKKeySequenceNumber     OBJECT-TYPE
        SYNTAX              Integer32 (0..15)
        MAX-ACCESS          read-only
        STATUS              current
        DESCRIPTION
             "The value of this object is the most recent TEK
        key sequence number for this TEK FSM."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.2.10 and 4.2.2.13."
        ::= { docsBpi2CmTEKEntry 6 }

   docsBpi2CmTEKExpiresOld  OBJECT-TYPE
        SYNTAX         DateAndTime
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the actual clock time for
        expiration of the immediate predecessor of the most recent
        TEK for this FSM.  If this FSM has only one TEK, then the
        value is the time of activation of this FSM."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.1.5 and 4.2.2.9."
        ::= { docsBpi2CmTEKEntry 7 }

   docsBpi2CmTEKExpiresNew  OBJECT-TYPE
        SYNTAX         DateAndTime
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the actual clock time for
        expiration of the most recent TEK for this FSM."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.1.5 and 4.2.2.9."
        ::= { docsBpi2CmTEKEntry 8 }

   docsBpi2CmTEKKeyRequests OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the number of times the CM
        has transmitted a Key Request message.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.4."
        ::= { docsBpi2CmTEKEntry 9 }

   docsBpi2CmTEKKeyReplies  OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the number of times the CM
        has received a Key Reply message, including a message whose
        authentication failed.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.5."
        ::= { docsBpi2CmTEKEntry 10 }

   docsBpi2CmTEKKeyRejects  OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the number of times the CM
        has received a Key Reject message, including a message
        whose authentication failed.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.6."
        ::= { docsBpi2CmTEKEntry 11 }

   docsBpi2CmTEKInvalids    OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the number of times the CM
        has received a TEK Invalid message, including a message
        whose authentication failed.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.8."
        ::= { docsBpi2CmTEKEntry 12 }

   docsBpi2CmTEKAuthPends   OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the count of times an
        Authorization Pending (Auth Pend) event occurred in this
        FSM.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of

        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.1.3.3.3."
        ::= { docsBpi2CmTEKEntry 13 }

   docsBpi2CmTEKKeyRejectErrorCode    OBJECT-TYPE
        SYNTAX         INTEGER {
                               none(1),
                               unknown(2),
                               unauthorizedSaid(4)
                               }
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the enumerated
        description of the Error-Code in the most recent Key Reject
        message received by the CM.  This has the value unknown(2) if
        the last Error-Code value was 0 and none(1) if no Key
        Reject message has been received since registration."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.1.2.6 and 4.2.2.15."
        ::= { docsBpi2CmTEKEntry 14 }

   docsBpi2CmTEKKeyRejectErrorString  OBJECT-TYPE
        SYNTAX         SnmpAdminString (SIZE (0..128))
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the text string in the
        most recent Key Reject message received by the CM.  This is
        a zero length string if no Key Reject message has been
        received since registration."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.1.2.6 and 4.2.2.6."
        ::= { docsBpi2CmTEKEntry 15 }

   docsBpi2CmTEKInvalidErrorCode OBJECT-TYPE
        SYNTAX         INTEGER {
                               none(1),
                               unknown(2),
                               invalidKeySequence(6)
                               }
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the enumerated
        description of the Error-Code in the most recent TEK Invalid
        message received by the CM.  This has the value unknown(2) if
        the last Error-Code value was 0 and none(1) if no TEK
        Invalid message has been received since registration."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.1.2.8 and 4.2.2.15."
        ::= { docsBpi2CmTEKEntry 16 }

   docsBpi2CmTEKInvalidErrorString    OBJECT-TYPE
        SYNTAX         SnmpAdminString (SIZE (0..128))
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the text string in the
        most recent TEK Invalid message received by the CM.  This is
        a zero length string if no TEK Invalid message has been
        received since registration."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.1.2.8 and 4.2.2.6."
        ::= { docsBpi2CmTEKEntry 17 }

   --
   -- The CM Multicast Objects Group
   --

   docsBpi2CmMulticastObjects OBJECT IDENTIFIER
        ::= { docsBpi2CmObjects 3 }

   --
   -- The CM Dynamic IP Multicast Mapping Table, indexed by
   -- docsBpi2CmIpMulticastIndex and by ifIndex
   --

   docsBpi2CmIpMulticastMapTable OBJECT-TYPE
        SYNTAX         SEQUENCE OF DocsBpi2CmIpMulticastMapEntry
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
             "This table maps multicast IP addresses to SAIDs per
        CM MAC Interface.
        It is intended to map multicast IP addresses associated
        with SA MAP Request messages."
        ::= { docsBpi2CmMulticastObjects 1 }

   docsBpi2CmIpMulticastMapEntry OBJECT-TYPE
        SYNTAX         DocsBpi2CmIpMulticastMapEntry
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
             "Each entry contains objects describing the mapping of
        one multicast IP address to one SAID, as well as
        associated state, message counters, and error information.

        An entry may be removed from this table upon the reception
        of an SA Map Reject."
        INDEX     { ifIndex, docsBpi2CmIpMulticastIndex }
        ::= { docsBpi2CmIpMulticastMapTable 1 }

   DocsBpi2CmIpMulticastMapEntry ::= SEQUENCE {
        docsBpi2CmIpMulticastIndex               Unsigned32,
        docsBpi2CmIpMulticastAddressType         InetAddressType,
        docsBpi2CmIpMulticastAddress             InetAddress,
        docsBpi2CmIpMulticastSAId                DocsSAIdOrZero,
        docsBpi2CmIpMulticastSAMapState          INTEGER,
        docsBpi2CmIpMulticastSAMapRequests       Counter32,
        docsBpi2CmIpMulticastSAMapReplies        Counter32,
        docsBpi2CmIpMulticastSAMapRejects        Counter32,
        docsBpi2CmIpMulticastSAMapRejectErrorCode INTEGER,
        docsBpi2CmIpMulticastSAMapRejectErrorString SnmpAdminString
        }

   docsBpi2CmIpMulticastIndex         OBJECT-TYPE
        SYNTAX         Unsigned32 (1..4294967295)
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
             "The index of this row."
        ::= { docsBpi2CmIpMulticastMapEntry 1 }

   docsBpi2CmIpMulticastAddressType   OBJECT-TYPE
        SYNTAX         InetAddressType
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The type of Internet address for
        docsBpi2CmIpMulticastAddress."
        ::= { docsBpi2CmIpMulticastMapEntry 2 }

   docsBpi2CmIpMulticastAddress  OBJECT-TYPE
        SYNTAX         InetAddress
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "This object represents the IP multicast address
        to be mapped.  The type of this address is determined by
        the value of the docsBpi2CmIpMulticastAddressType object."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 5.4."
        ::= { docsBpi2CmIpMulticastMapEntry 3 }

   docsBpi2CmIpMulticastSAId          OBJECT-TYPE
        SYNTAX         DocsSAIdOrZero
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "This object represents the SAID to which the IP
        multicast address has been mapped.  If no SA Map Reply has
        been received for the IP address, this object should have
        the value 0."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.2.12."
        ::= { docsBpi2CmIpMulticastMapEntry 4 }

   docsBpi2CmIpMulticastSAMapState         OBJECT-TYPE
        SYNTAX         INTEGER {
                              start(1),
                              mapWait(2),
                              mapped(3)
                       }
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the state of the SA
        Mapping FSM for this IP."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 5.3.1."
        ::= { docsBpi2CmIpMulticastMapEntry 5 }

   docsBpi2CmIpMulticastSAMapRequests OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the number of times the
        CM has transmitted an SA Map Request message for this IP.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of

        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.10."
        ::= { docsBpi2CmIpMulticastMapEntry 6 }

   docsBpi2CmIpMulticastSAMapReplies  OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the number of times the
        CM has received an SA Map Reply message for this IP.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.11."
        ::= { docsBpi2CmIpMulticastMapEntry 7 }

   docsBpi2CmIpMulticastSAMapRejects  OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the number of times the
        CM has received an SA MAP Reject message for this IP.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.12."
        ::= { docsBpi2CmIpMulticastMapEntry 8 }

   docsBpi2CmIpMulticastSAMapRejectErrorCode    OBJECT-TYPE
        SYNTAX         INTEGER {
                       none(1),
                       unknown(2),
                       noAuthForRequestedDSFlow(9),
                       dsFlowNotMappedToSA(10)
                       }
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the enumerated
        description of the Error-Code in the most recent SA Map
        Reject message sent in response to an SA Map Request for
        This IP.  It has the value none(1) if no SA MAP Reject
        message has been received since entry creation."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.1.12 and 4.2.2.15."
        ::= { docsBpi2CmIpMulticastMapEntry 9 }

   docsBpi2CmIpMulticastSAMapRejectErrorString  OBJECT-TYPE
        SYNTAX         SnmpAdminString (SIZE (0..128))
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the text string in
        the most recent SA Map Reject message sent in response to
        an SA Map Request for this IP.  It is a zero length string
        if no SA Map Reject message has been received since entry
        creation."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.1.12 and 4.2.2.6."
        ::= { docsBpi2CmIpMulticastMapEntry 10 }

   --
   -- CM Cert Objects
   --

   docsBpi2CmCertObjects OBJECT IDENTIFIER
        ::= { docsBpi2CmObjects 4 }

   --
   -- CM Device Cert Table
   --

   docsBpi2CmDeviceCertTable  OBJECT-TYPE
        SYNTAX                SEQUENCE OF DocsBpi2CmDeviceCertEntry
        MAX-ACCESS            not-accessible
        STATUS                current
        DESCRIPTION
             "This table describes the Baseline Privacy Plus
        device certificates for each CM MAC interface."
        ::= { docsBpi2CmCertObjects 1 }

   docsBpi2CmDeviceCertEntry  OBJECT-TYPE
        SYNTAX              DocsBpi2CmDeviceCertEntry
        MAX-ACCESS          not-accessible
        STATUS              current
        DESCRIPTION
             "Each entry contains the device certificates of
        one CM MAC interface.  An entry in this table exists for
        each ifEntry with an ifType of docsCableMaclayer(127)."
        INDEX               { ifIndex }
        ::= { docsBpi2CmDeviceCertTable 1 }

   DocsBpi2CmDeviceCertEntry ::= SEQUENCE {
        docsBpi2CmDeviceCmCert
                              DocsX509ASN1DEREncodedCertificate,
        docsBpi2CmDeviceManufCert
                              DocsX509ASN1DEREncodedCertificate
        }

   docsBpi2CmDeviceCmCert   OBJECT-TYPE
        SYNTAX        DocsX509ASN1DEREncodedCertificate
        MAX-ACCESS         read-write
        STATUS              current
        DESCRIPTION
             "The X509 DER-encoded cable modem certificate.
        Note:  This object can be set only when the value is the
        zero-length OCTET STRING; otherwise, an error of
        'inconsistentValue' is returned.  Once the object
        contains the certificate, its access MUST be read-only
        and persists after re-initialization of the
        managed system."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 9.1."
        ::= { docsBpi2CmDeviceCertEntry 1 }

   docsBpi2CmDeviceManufCert     OBJECT-TYPE
        SYNTAX         DocsX509ASN1DEREncodedCertificate
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The X509 DER-encoded manufacturer certificate that
        signed the cable modem certificate."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 9.1."
        ::= { docsBpi2CmDeviceCertEntry 2 }

   --
   -- CM Crypto Suite Table
   --

   docsBpi2CmCryptoSuiteTable    OBJECT-TYPE
        SYNTAX         SEQUENCE OF    DocsBpi2CmCryptoSuiteEntry
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
             "This table describes the Baseline Privacy Plus
        cryptographic suite capabilities for each CM MAC
        interface."
        ::= { docsBpi2CmObjects 5 }

   docsBpi2CmCryptoSuiteEntry    OBJECT-TYPE
        SYNTAX         DocsBpi2CmCryptoSuiteEntry
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
             "Each entry contains a cryptographic suite pair
        that this CM MAC supports."
        INDEX     { ifIndex, docsBpi2CmCryptoSuiteIndex }
        ::= { docsBpi2CmCryptoSuiteTable 1 }

   DocsBpi2CmCryptoSuiteEntry ::= SEQUENCE {
        docsBpi2CmCryptoSuiteIndex              Unsigned32,
        docsBpi2CmCryptoSuiteDataEncryptAlg
                                    DocsBpkmDataEncryptAlg,
        docsBpi2CmCryptoSuiteDataAuthentAlg
                                    DocsBpkmDataAuthentAlg
        }

   docsBpi2CmCryptoSuiteIndex OBJECT-TYPE
        SYNTAX         Unsigned32 (1..1000)
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
             "The index for a cryptographic suite row."
        ::= { docsBpi2CmCryptoSuiteEntry 1 }

   docsBpi2CmCryptoSuiteDataEncryptAlg     OBJECT-TYPE
        SYNTAX    DocsBpkmDataEncryptAlg
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the data encryption
        algorithm for this cryptographic suite capability."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.2.20."
        ::= { docsBpi2CmCryptoSuiteEntry 2 }

   docsBpi2CmCryptoSuiteDataAuthentAlg     OBJECT-TYPE
        SYNTAX    DocsBpkmDataAuthentAlg
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the data authentication
        algorithm for this cryptographic suite capability."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.2.20."
        ::= { docsBpi2CmCryptoSuiteEntry 3 }

   -- Cable Modem Termination System Group

docsBpi2CmtsObjects OBJECT IDENTIFIER ::= { docsBpi2MIBObjects 2 }

   --
   -- SPECIAL NOTE:  For the following CMTS tables, when a CM is
   -- running in BPI mode, replace SAID (Security Association ID)
   -- with SID (Service ID).  The CMTS is required to map SAIDs and
   -- SIDs to one contiguous space.
   --

   --
   -- The BPI+ base table for CMTSs, indexed by ifIndex
   --

   docsBpi2CmtsBaseTable    OBJECT-TYPE
        SYNTAX              SEQUENCE OF    DocsBpi2CmtsBaseEntry
        MAX-ACCESS          not-accessible
        STATUS              current
        DESCRIPTION
             "This table describes the basic Baseline Privacy
        attributes of each CMTS MAC interface."
        ::= { docsBpi2CmtsObjects 1 }

   docsBpi2CmtsBaseEntry    OBJECT-TYPE
        SYNTAX              DocsBpi2CmtsBaseEntry
        MAX-ACCESS          not-accessible
        STATUS              current
        DESCRIPTION
             "Each entry contains objects describing attributes of
        one CMTS MAC interface.  An entry in this table exists for
        each ifEntry with an ifType of docsCableMaclayer(127)."
        INDEX     { ifIndex }
        ::= { docsBpi2CmtsBaseTable 1 }

   DocsBpi2CmtsBaseEntry ::= SEQUENCE {

        docsBpi2CmtsDefaultAuthLifetime              Integer32,
        docsBpi2CmtsDefaultTEKLifetime               Integer32,
        docsBpi2CmtsDefaultSelfSignedManufCertTrust  INTEGER,
            docsBpi2CmtsCheckCertValidityPeriods         TruthValue,
            docsBpi2CmtsAuthentInfos                     Counter32,
            docsBpi2CmtsAuthRequests                     Counter32,
            docsBpi2CmtsAuthReplies                      Counter32,
            docsBpi2CmtsAuthRejects                      Counter32,
            docsBpi2CmtsAuthInvalids                     Counter32,
            docsBpi2CmtsSAMapRequests                    Counter32,
            docsBpi2CmtsSAMapReplies                     Counter32,
            docsBpi2CmtsSAMapRejects                     Counter32
            }

   docsBpi2CmtsDefaultAuthLifetime    OBJECT-TYPE
        SYNTAX         Integer32 (1..6048000)
        UNITS          "seconds"
        MAX-ACCESS     read-write
        STATUS         current
        DESCRIPTION
             "The value of this object is the default lifetime, in
        seconds, that the CMTS assigns to a new authorization key.
        This object value persists after re-initialization of the
        managed system."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Appendix A.2."
        DEFVAL { 604800 }
        ::= { docsBpi2CmtsBaseEntry 1 }

   docsBpi2CmtsDefaultTEKLifetime     OBJECT-TYPE
        SYNTAX         Integer32 (1..604800)
        UNITS          "seconds"
        MAX-ACCESS     read-write
        STATUS         current
        DESCRIPTION
             "The value of this object is the default lifetime, in
        seconds, that the CMTS assigns to a new Traffic Encryption
        Key (TEK).
        This object value persists after re-initialization of the
        managed system."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Appendix A.2."
        DEFVAL { 43200 }
        ::= { docsBpi2CmtsBaseEntry 2 }

   docsBpi2CmtsDefaultSelfSignedManufCertTrust  OBJECT-TYPE
        SYNTAX    INTEGER {
                  trusted (1),
                  untrusted (2)
                  }
        MAX-ACCESS     read-write
        STATUS         current
        DESCRIPTION
             "This object determines the default trust of
        self-signed manufacturer certificate entries, contained
        in docsBpi2CmtsCACertTable, and created after this
        object is set.
        This object need not persist after re-initialization
        of the managed system."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 9.4.1"
        ::= { docsBpi2CmtsBaseEntry 3 }

   docsBpi2CmtsCheckCertValidityPeriods    OBJECT-TYPE
        SYNTAX         TruthValue
        MAX-ACCESS     read-write
        STATUS         current
        DESCRIPTION
             "Setting this object to 'true' causes all chained and
        root certificates in the chain to have their validity
        periods checked against the current time of day, when
        the CMTS receives an Authorization Request from the
        CM.
        A 'false' setting causes all certificates in the chain
        not to have their validity periods checked against the
        current time of day.
        This object need not persist after re-initialization
        of the managed system."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 9.4.2"
        ::= { docsBpi2CmtsBaseEntry 4 }

   docsBpi2CmtsAuthentInfos OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the number of times the
        CMTS has received an Authentication Information message
        from any CM.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other

        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.9."
        ::= { docsBpi2CmtsBaseEntry 5 }

   docsBpi2CmtsAuthRequests OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
                "The value of this object is the number of times the
        CMTS has received an Authorization Request message from any
        CM.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.1."
        ::= { docsBpi2CmtsBaseEntry 6 }

   docsBpi2CmtsAuthReplies  OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
               "The value of this object is the number of times the
        CMTS has transmitted an Authorization Reply message to any
        CM.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.2."
        ::= { docsBpi2CmtsBaseEntry 7 }

   docsBpi2CmtsAuthRejects  OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
                "The value of this object is the number of times the
        CMTS has transmitted an Authorization Reject message to any

        CM.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.3."
        ::= { docsBpi2CmtsBaseEntry 8 }

   docsBpi2CmtsAuthInvalids OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
                 "The value of this object is the number of times
        the CMTS has transmitted an Authorization Invalid message
        to any CM.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.7."
        ::= { docsBpi2CmtsBaseEntry 9 }

   docsBpi2CmtsSAMapRequests     OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the number of times the
        CMTS has received an SA Map Request message from any CM.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.10."
        ::= { docsBpi2CmtsBaseEntry 10 }

   docsBpi2CmtsSAMapReplies OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the number of times the
        CMTS has transmitted an SA Map Reply message to any CM.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.11."
        ::= { docsBpi2CmtsBaseEntry 11 }

   docsBpi2CmtsSAMapRejects OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the number of times the
        CMTS has transmitted an SA Map Reject message to any CM.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.12."
        ::= { docsBpi2CmtsBaseEntry 12 }

   --
   -- The CMTS Authorization Table, indexed by ifIndex and CM MAC
   -- address
   --

   docsBpi2CmtsAuthTable    OBJECT-TYPE
        SYNTAX         SEQUENCE OF    DocsBpi2CmtsAuthEntry
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
             "This table describes the attributes of each CM
        authorization association.  The CMTS maintains one
        authorization association with each Baseline Privacy-
        enabled CM, registered on each CMTS MAC interface,
        regardless of whether the CM is authorized or rejected."
        ::= { docsBpi2CmtsObjects 2 }

   docsBpi2CmtsAuthEntry    OBJECT-TYPE
        SYNTAX              DocsBpi2CmtsAuthEntry
        MAX-ACCESS          not-accessible
        STATUS              current
        DESCRIPTION
             "Each entry contains objects describing attributes of
        one authorization association.  The CMTS MUST create one
        entry per CM per MAC interface, based on the receipt of an
        Authorization Request message, and MUST not delete the
        entry until the CM loses registration."
        INDEX     { ifIndex, docsBpi2CmtsAuthCmMacAddress }
        ::= { docsBpi2CmtsAuthTable 1 }

   DocsBpi2CmtsAuthEntry ::= SEQUENCE {
        docsBpi2CmtsAuthCmMacAddress        MacAddress,
        docsBpi2CmtsAuthCmBpiVersion        INTEGER,
        docsBpi2CmtsAuthCmPublicKey         OCTET STRING,
        docsBpi2CmtsAuthCmKeySequenceNumber Integer32,
        docsBpi2CmtsAuthCmExpiresOld        DateAndTime,
        docsBpi2CmtsAuthCmExpiresNew        DateAndTime,
        docsBpi2CmtsAuthCmLifetime          Integer32,
        docsBpi2CmtsAuthCmReset             INTEGER,
        docsBpi2CmtsAuthCmInfos             Counter32,
        docsBpi2CmtsAuthCmRequests          Counter32,
        docsBpi2CmtsAuthCmReplies           Counter32,
        docsBpi2CmtsAuthCmRejects           Counter32,
        docsBpi2CmtsAuthCmInvalids          Counter32,
        docsBpi2CmtsAuthRejectErrorCode     INTEGER,
        docsBpi2CmtsAuthRejectErrorString   SnmpAdminString,
        docsBpi2CmtsAuthInvalidErrorCode    INTEGER,
        docsBpi2CmtsAuthInvalidErrorString  SnmpAdminString,
        docsBpi2CmtsAuthPrimarySAId         DocsSAIdOrZero,
        docsBpi2CmtsAuthBpkmCmCertValid     INTEGER,
        docsBpi2CmtsAuthBpkmCmCert
                             DocsX509ASN1DEREncodedCertificate,
        docsBpi2CmtsAuthCACertIndexPtr      Unsigned32
        }

   docsBpi2CmtsAuthCmMacAddress  OBJECT-TYPE
        SYNTAX         MacAddress
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
             "The value of this object is the physical address of
        the CM to which the authorization association applies."
        ::= { docsBpi2CmtsAuthEntry 1 }

   docsBpi2CmtsAuthCmBpiVersion  OBJECT-TYPE
        SYNTAX         INTEGER {
                         bpi (0),
                         bpiPlus (1)
                          }
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the version of Baseline
        Privacy for which this CM has registered.  The value
        'bpiplus' represents the value of BPI-Version Attribute of
        the Baseline Privacy Key Management BPKM attribute
        BPI-Version (1).  The value 'bpi' is used to represent the
        CM registered using DOCSIS 1.0 Baseline Privacy."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.2.22; ANSI/SCTE 22-2 2002(formerly DSS 02-03)
        Data-Over-Cable Service Interface Specification DOCSIS 1.0
        Baseline Privacy Interface (BPI)"
        ::= { docsBpi2CmtsAuthEntry 2 }

   docsBpi2CmtsAuthCmPublicKey   OBJECT-TYPE
        SYNTAX         OCTET STRING (SIZE (0..524))
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is a DER-encoded
        RSAPublicKey ASN.1 type string, as defined in the RSA
        Encryption Standard (PKCS #1), corresponding to the
        public key of the CM.  This is the zero-length OCTET
        STRING if the CMTS does not retain the public key."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.2.4."
        ::= { docsBpi2CmtsAuthEntry 3 }

   docsBpi2CmtsAuthCmKeySequenceNumber     OBJECT-TYPE
        SYNTAX         Integer32 (0..15)
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the most recent
        authorization key sequence number for this CM."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.1.2 and 4.2.2.10."
        ::= { docsBpi2CmtsAuthEntry 4 }

   docsBpi2CmtsAuthCmExpiresOld  OBJECT-TYPE
        SYNTAX         DateAndTime
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the actual clock time
        for expiration of the immediate predecessor of the most
        recent authorization key for this FSM.  If this FSM has only
        one authorization key, then the value is the time of
        activation of this FSM.
        Note: This object has no meaning for CMs running in BPI
        mode; therefore, this object is not instantiated for entries
        associated to those CMs."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.1.2 and 4.2.2.9."
        ::= { docsBpi2CmtsAuthEntry 5 }

   docsBpi2CmtsAuthCmExpiresNew  OBJECT-TYPE
        SYNTAX         DateAndTime
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
                  "The value of this object is the actual clock
        time for expiration of the most recent authorization key
        for this FSM."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.1.2 and 4.2.2.9."
        ::= { docsBpi2CmtsAuthEntry 6 }

   docsBpi2CmtsAuthCmLifetime    OBJECT-TYPE
        SYNTAX         Integer32 (1..6048000)
        UNITS          "seconds"
        MAX-ACCESS     read-write
        STATUS         current
        DESCRIPTION
             "The value of this object is the lifetime, in seconds,
        that the CMTS assigns to an authorization key for this CM."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.2 and Appendix A.2."
        ::= { docsBpi2CmtsAuthEntry 7 }

   docsBpi2CmtsAuthCmReset  OBJECT-TYPE
        SYNTAX    INTEGER   {
                            noResetRequested(1),
                            invalidateAuth(2),
                            sendAuthInvalid(3),
                            invalidateTeks(4)
                            }
        MAX-ACCESS     read-write
        STATUS         current
        DESCRIPTION
             "Setting this object to invalidateAuth(2) causes the
        CMTS to invalidate the current CM authorization key(s), but
        not to transmit an Authorization Invalid message nor to
        invalidate the primary SAID's TEKs.  Setting this object to
        sendAuthInvalid(3) causes the CMTS to invalidate the
        current CM authorization key(s), and to transmit an
        Authorization Invalid message to the CM, but not to
        invalidate the primary SAID's TEKs.  Setting this object to
        invalidateTeks(4) causes the CMTS to invalidate the current
        CM authorization key(s), to transmit an Authorization
        Invalid message to the CM, and to invalidate the TEKs
        associated with this CM's primary SAID.
        For BPI mode, substitute all of the CM's unicast
        TEKs for the primary SAID's TEKs in the previous
        paragraph.
        Reading this object returns the most recently set
        value of this object or, if the object has not been set
        since entry creation, returns noResetRequested(1)."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.1.2.3.4, 4.1.2.3.5, and 4.1.3.3.5."
        ::= { docsBpi2CmtsAuthEntry 8 }

   docsBpi2CmtsAuthCmInfos       OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the number of times the
        CMTS has received an Authentication Information message
        from this CM.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.9."
        ::= { docsBpi2CmtsAuthEntry 9 }

   docsBpi2CmtsAuthCmRequests    OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the number of times the
        CMTS has received an Authorization Request message from

        this CM.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.1."
        ::= { docsBpi2CmtsAuthEntry 10 }

   docsBpi2CmtsAuthCmReplies     OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the number of times the
        CMTS has transmitted an Authorization Reply message to this
        CM.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.2."
        ::= { docsBpi2CmtsAuthEntry 11 }

   docsBpi2CmtsAuthCmRejects     OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the number of times the
        CMTS has transmitted an Authorization Reject message to
        this CM.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.3."
        ::= { docsBpi2CmtsAuthEntry 12 }

   docsBpi2CmtsAuthCmInvalids    OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the number of times the
        CMTS has transmitted an Authorization Invalid message to
        this CM.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.7."
        ::= { docsBpi2CmtsAuthEntry 13 }

   docsBpi2CmtsAuthRejectErrorCode    OBJECT-TYPE
        SYNTAX         INTEGER {
                               none(1),
                               unknown(2),
                               unauthorizedCm(3),
                               unauthorizedSaid(4),
                               permanentAuthorizationFailure(8),
                               timeOfDayNotAcquired(11)
                               }
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the enumerated
        description of the Error-Code in the most recent
        Authorization Reject message transmitted to the CM.  This has
        the value unknown(2) if the last Error-Code value was 0 and
        none(1) if no Authorization Reject message has been
        transmitted to the CM since entry creation."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.1.3 and 4.2.2.15."
        ::= { docsBpi2CmtsAuthEntry 14 }

   docsBpi2CmtsAuthRejectErrorString  OBJECT-TYPE
        SYNTAX         SnmpAdminString (SIZE (0..128))
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the text string in the
        most recent Authorization Reject message transmitted to the
        CM.  This is a zero length string if no Authorization
        Reject message has been transmitted to the CM since entry
        creation."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.1.3 and 4.2.2.6."
        ::= { docsBpi2CmtsAuthEntry 15 }

   docsBpi2CmtsAuthInvalidErrorCode   OBJECT-TYPE
        SYNTAX         INTEGER {
                               none(1),
                               unknown(2),
                               unauthorizedCm(3),
                               unsolicited(5),
                               invalidKeySequence(6),
                               keyRequestAuthenticationFailure(7)
                               }
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the enumerated
        description of the Error-Code in the most recent
        Authorization Invalid message transmitted to the CM.  This
        has the value unknown(2) if the last Error-Code value was 0
        and none(1) if no Authorization Invalid message has been
        transmitted to the CM since entry creation."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.1.7 and 4.2.2.15."
        ::= { docsBpi2CmtsAuthEntry 16 }

   docsBpi2CmtsAuthInvalidErrorString OBJECT-TYPE
        SYNTAX         SnmpAdminString (SIZE (0..128))
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the text string in the
        most recent Authorization Invalid message transmitted to
        the CM.  This is a zero length string if no Authorization
        Invalid message has been transmitted to the CM since entry
        creation."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.1.7 and 4.2.2.6."
        ::= { docsBpi2CmtsAuthEntry 17 }

   docsBpi2CmtsAuthPrimarySAId   OBJECT-TYPE
        SYNTAX         DocsSAIdOrZero
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the Primary Security
        Association identifier.  For BPI mode, the value must be

        any unicast SID."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 2.1.3."
        ::= { docsBpi2CmtsAuthEntry 18 }

   docsBpi2CmtsAuthBpkmCmCertValid         OBJECT-TYPE
        SYNTAX    INTEGER {
                          unknown (0),
                          validCmChained (1),
                          validCmTrusted (2),
                          invalidCmUntrusted (3),
                          invalidCAUntrusted (4),
                          invalidCmOther (5),
                          invalidCAOther (6)
                          }
        MAX-ACCESS     read-only
        STATUS    current
        DESCRIPTION
             "Contains the reason why a CM's certificate is deemed
        valid or invalid.
        Return unknown(0) if the CM is running BPI mode.
        ValidCmChained(1) means the certificate is valid
           because it chains to a valid certificate.
        ValidCmTrusted(2) means the certificate is valid
           because it has been provisioned (in the
           docsBpi2CmtsProvisionedCmCert table) to be trusted.
        InvalidCmUntrusted(3) means the certificate is invalid
           because it has been provisioned (in the
           docsBpi2CmtsProvisionedCmCert table) to be untrusted.
        InvalidCAUntrusted(4) means the certificate is invalid
           because it chains to an untrusted certificate.
        InvalidCmOther(5) and InvalidCAOther(6) refer to
           errors in parsing, validity periods, etc., which are
           attributable to the CM certificate or its chain,
           respectively; additional information may be found
           in docsBpi2AuthRejectErrorString for these types
           of errors."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 9.4.2."
        ::= { docsBpi2CmtsAuthEntry 19 }

   docsBpi2CmtsAuthBpkmCmCert    OBJECT-TYPE
        SYNTAX         DocsX509ASN1DEREncodedCertificate
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The X509 CM Certificate sent as part of a BPKM
        Authorization Request.
        Note: The zero-length OCTET STRING must be returned if the
        Entire certificate is not retained in the CMTS."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 9.2."
        ::= { docsBpi2CmtsAuthEntry 20 }

   docsBpi2CmtsAuthCACertIndexPtr    OBJECT-TYPE
        SYNTAX         Unsigned32 (0..4294967295)
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "A row index into docsBpi2CmtsCACertTable.
              Returns the index in docsBpi2CmtsCACertTable to which
              CA certificate this CM is chained to.  A value of
              0 means it could not be found or not applicable."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 9.2."
        ::= { docsBpi2CmtsAuthEntry 21 }

   --
   -- The CMTS TEK Table, indexed by ifIndex and SAID
   --

   docsBpi2CmtsTEKTable     OBJECT-TYPE
        SYNTAX         SEQUENCE OF    DocsBpi2CmtsTEKEntry
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
             "This table describes the attributes of each
        Traffic Encryption Key (TEK) association.  The CMTS
        Maintains one TEK association per SAID on each CMTS MAC
        interface."
        ::= { docsBpi2CmtsObjects 3 }

   docsBpi2CmtsTEKEntry     OBJECT-TYPE
        SYNTAX         DocsBpi2CmtsTEKEntry
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
             "Each entry contains objects describing attributes of
        one TEK association on a particular CMTS MAC interface.  The
        CMTS MUST create one entry per SAID per MAC interface,
        based on the receipt of a Key Request message, and MUST not
        delete the entry before the CM authorization for the SAID

        permanently expires."
        INDEX     { ifIndex, docsBpi2CmtsTEKSAId }
        ::= { docsBpi2CmtsTEKTable 1 }

   DocsBpi2CmtsTEKEntry ::= SEQUENCE {
        docsBpi2CmtsTEKSAId                DocsSAId,
        docsBpi2CmtsTEKSAType              DocsBpkmSAType,
        docsBpi2CmtsTEKDataEncryptAlg      DocsBpkmDataEncryptAlg,
        docsBpi2CmtsTEKDataAuthentAlg      DocsBpkmDataAuthentAlg,
        docsBpi2CmtsTEKLifetime            Integer32,
        docsBpi2CmtsTEKKeySequenceNumber   Integer32,
        docsBpi2CmtsTEKExpiresOld          DateAndTime,
        docsBpi2CmtsTEKExpiresNew          DateAndTime,
        docsBpi2CmtsTEKReset               TruthValue,
        docsBpi2CmtsKeyRequests            Counter32,
        docsBpi2CmtsKeyReplies             Counter32,
        docsBpi2CmtsKeyRejects             Counter32,
        docsBpi2CmtsTEKInvalids            Counter32,
        docsBpi2CmtsKeyRejectErrorCode     INTEGER,
        docsBpi2CmtsKeyRejectErrorString   SnmpAdminString,
        docsBpi2CmtsTEKInvalidErrorCode    INTEGER,
        docsBpi2CmtsTEKInvalidErrorString  SnmpAdminString
   }

   docsBpi2CmtsTEKSAId OBJECT-TYPE
        SYNTAX         DocsSAId
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
             "The value of this object is the DOCSIS Security
        Association ID (SAID)."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.2.12."
        ::= { docsBpi2CmtsTEKEntry 1 }

   docsBpi2CmtsTEKSAType    OBJECT-TYPE
        SYNTAX         DocsBpkmSAType
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the type of security
        association.  'dynamic' does not apply to CMs running in
        BPI mode.  Unicast BPI TEKs must utilize the 'primary'
        encoding, and multicast BPI TEKs must utilize the 'static'
        encoding."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 2.1.3."
        ::= { docsBpi2CmtsTEKEntry 2 }

   docsBpi2CmtsTEKDataEncryptAlg OBJECT-TYPE
        SYNTAX    DocsBpkmDataEncryptAlg
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the data encryption
        algorithm for this SAID."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.2.20."
        ::= { docsBpi2CmtsTEKEntry 3 }

   docsBpi2CmtsTEKDataAuthentAlg OBJECT-TYPE
        SYNTAX    DocsBpkmDataAuthentAlg
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the data authentication
        algorithm for this SAID."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.2.20."
        ::= { docsBpi2CmtsTEKEntry 4 }

   docsBpi2CmtsTEKLifetime  OBJECT-TYPE
        SYNTAX         Integer32 (1..604800)
        UNITS          "seconds"
        MAX-ACCESS     read-write
        STATUS         current
        DESCRIPTION
             "The value of this object is the lifetime, in
        seconds, that the CMTS assigns to keys for this TEK
        association."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.5 and Appendix A.2."
        ::= { docsBpi2CmtsTEKEntry 5 }

   docsBpi2CmtsTEKKeySequenceNumber   OBJECT-TYPE
        SYNTAX              Integer32 (0..15)
        MAX-ACCESS          read-only
        STATUS              current
        DESCRIPTION
             "The value of this object is the most recent TEK

        key sequence number for this SAID."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.2.10 and 4.2.2.13."
        ::= { docsBpi2CmtsTEKEntry 6 }

   docsBpi2CmtsTEKExpiresOld     OBJECT-TYPE
        SYNTAX         DateAndTime
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the actual clock time
        for expiration of the immediate predecessor of the most
        recent TEK for this FSM.  If this FSM has only one TEK, then
        the value is the time of activation of this FSM."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.1.5 and 4.2.2.9."
        ::= { docsBpi2CmtsTEKEntry 7 }

   docsBpi2CmtsTEKExpiresNew     OBJECT-TYPE
        SYNTAX         DateAndTime
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the actual clock time
        for expiration of the most recent TEK for this FSM."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.1.5 and 4.2.2.9."
        ::= { docsBpi2CmtsTEKEntry 8 }

   docsBpi2CmtsTEKReset     OBJECT-TYPE
        SYNTAX         TruthValue
        MAX-ACCESS     read-write
        STATUS         current
        DESCRIPTION
             "Setting this object to 'true' causes the CMTS to
        invalidate all currently active TEKs and to generate new
        TEKs for the associated SAID; the CMTS MAY also generate
        unsolicited TEK Invalid messages, to optimize the TEK
        synchronization between the CMTS and the CM(s).  Reading
        this object always returns FALSE."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.1.3.3.5."
        ::= { docsBpi2CmtsTEKEntry 9 }

   docsBpi2CmtsKeyRequests  OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the number of times the
        CMTS has received a Key Request message.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.4."
        ::= { docsBpi2CmtsTEKEntry 10 }

   docsBpi2CmtsKeyReplies   OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the number of times the
        CMTS has transmitted a Key Reply message.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.5."
        ::= { docsBpi2CmtsTEKEntry 11 }

   docsBpi2CmtsKeyRejects   OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the number of times the
        CMTS has transmitted a Key Reject message.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.6."
        ::= { docsBpi2CmtsTEKEntry 12 }

   docsBpi2CmtsTEKInvalids  OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the number of times the
        CMTS has transmitted a TEK Invalid message.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.8."
        ::= { docsBpi2CmtsTEKEntry 13 }

   docsBpi2CmtsKeyRejectErrorCode     OBJECT-TYPE
        SYNTAX         INTEGER {
                               none(1),
                               unknown(2),
                               unauthorizedSaid(4)
                               }
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the enumerated
        description of the Error-Code in the most recent Key Reject
        message sent in response to a Key Request for this SAID.
        This has the value unknown(2) if the last Error-Code value
        was 0 and none(1) if no Key Reject message has been
        received since registration."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.1.6 and 4.2.2.15."
        ::= { docsBpi2CmtsTEKEntry 14 }

   docsBpi2CmtsKeyRejectErrorString   OBJECT-TYPE
        SYNTAX         SnmpAdminString (SIZE (0..128))
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the text string in
        the most recent Key Reject message sent in response to a
        Key Request for this SAID.  This is a zero length string if
        no Key Reject message has been received since
        registration."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.1.6 and 4.2.2.6."
        ::= { docsBpi2CmtsTEKEntry 15 }

   docsBpi2CmtsTEKInvalidErrorCode    OBJECT-TYPE
        SYNTAX         INTEGER {
                               none(1),
                               unknown(2),
                               invalidKeySequence(6)
                               }
        MAX-ACCESS          read-only
        STATUS              current
        DESCRIPTION
             "The value of this object is the enumerated
        description of the Error-Code in the most recent TEK
        Invalid message sent in association with this SAID.  This
        has the value unknown(2) if the last Error-Code value was 0
        and none(1) if no TEK Invalid message has been received
        since registration."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.1.8 and 4.2.2.15."
        ::= { docsBpi2CmtsTEKEntry 16 }

   docsBpi2CmtsTEKInvalidErrorString  OBJECT-TYPE
        SYNTAX         SnmpAdminString (SIZE (0..128))
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the text string in
        the most recent TEK Invalid message sent in association
        with this SAID.  This is a zero length string if no TEK
        Invalid message has been received since registration."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.1.8 and 4.2.2.6."
        ::= { docsBpi2CmtsTEKEntry 17 }

   --
   -- The CMTS Multicast Objects Group
   --

   docsBpi2CmtsMulticastObjects OBJECT IDENTIFIER
        ::= { docsBpi2CmtsObjects 4 }

   --
   -- The CMTS IP Multicast Mapping Table, indexed by
   -- docsBpi2CmtsIpMulticastIndex, and by ifIndex
   --

   docsBpi2CmtsIpMulticastMapTable         OBJECT-TYPE
        SYNTAX         SEQUENCE OF DocsBpi2CmtsIpMulticastMapEntry
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
             "This table maps multicast IP addresses to SAIDs.
        If a multicast IP address is mapped by multiple rows
        in the table, the row with the lowest
        docsBpi2CmtsIpMulticastIndex must be utilized for the
        mapping."
        ::= { docsBpi2CmtsMulticastObjects 1 }

   docsBpi2CmtsIpMulticastMapEntry         OBJECT-TYPE
        SYNTAX         DocsBpi2CmtsIpMulticastMapEntry
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
             "Each entry contains objects describing the mapping of
        a set of multicast IP address and the mask to one SAID
        associated to a CMTS MAC Interface, as well as associated
        message counters and error information."
        INDEX     { ifIndex, docsBpi2CmtsIpMulticastIndex }
        ::= { docsBpi2CmtsIpMulticastMapTable 1 }

   DocsBpi2CmtsIpMulticastMapEntry ::= SEQUENCE {
        docsBpi2CmtsIpMulticastIndex            Unsigned32,
        docsBpi2CmtsIpMulticastAddressType      InetAddressType,
        docsBpi2CmtsIpMulticastAddress          InetAddress,
        docsBpi2CmtsIpMulticastMask             InetAddress,
        docsBpi2CmtsIpMulticastSAId             DocsSAIdOrZero,
        docsBpi2CmtsIpMulticastSAType           DocsBpkmSAType,
        docsBpi2CmtsIpMulticastDataEncryptAlg
                                        DocsBpkmDataEncryptAlg,
        docsBpi2CmtsIpMulticastDataAuthentAlg
                                        DocsBpkmDataAuthentAlg,
        docsBpi2CmtsIpMulticastSAMapRequests    Counter32,
        docsBpi2CmtsIpMulticastSAMapReplies     Counter32,
        docsBpi2CmtsIpMulticastSAMapRejects     Counter32,
        docsBpi2CmtsIpMulticastSAMapRejectErrorCode
                                                   INTEGER,
        docsBpi2CmtsIpMulticastSAMapRejectErrorString
                                                   SnmpAdminString,
        docsBpi2CmtsIpMulticastMapControl          RowStatus,
        docsBpi2CmtsIpMulticastMapStorageType      StorageType
        }

   docsBpi2CmtsIpMulticastIndex       OBJECT-TYPE
        SYNTAX         Unsigned32 (1..4294967295)
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
             "The index of this row.  Conceptual rows having the
        value 'permanent' need not allow write-access to any
        columnar objects in the row."
        ::= { docsBpi2CmtsIpMulticastMapEntry 1 }

   docsBpi2CmtsIpMulticastAddressType OBJECT-TYPE
        SYNTAX         InetAddressType
        MAX-ACCESS     read-create
        STATUS         current
        DESCRIPTION
             "The type of Internet address for
        docsBpi2CmtsIpMulticastAddress
        and docsBpi2CmtsIpMulticastMask."
        DEFVAL { ipv4 }
        ::= { docsBpi2CmtsIpMulticastMapEntry 2 }

   docsBpi2CmtsIpMulticastAddress          OBJECT-TYPE
        SYNTAX         InetAddress
        MAX-ACCESS     read-create
        STATUS         current
        DESCRIPTION
             "This object represents the IP multicast address
        to be mapped, in conjunction with
        docsBpi2CmtsIpMulticastMask.  The type of this address is
        determined by the value of the object
        docsBpi2CmtsIpMulticastAddressType."
        ::= { docsBpi2CmtsIpMulticastMapEntry 3 }

   docsBpi2CmtsIpMulticastMask        OBJECT-TYPE
        SYNTAX         InetAddress
        MAX-ACCESS     read-create
        STATUS         current
        DESCRIPTION
             "This object represents the IP multicast address mask
        for this row.
        An IP multicast address matches this row if the logical
        AND of the address with docsBpi2CmtsIpMulticastMask is
        identical to the logical AND of
        docsBpi2CmtsIpMulticastAddr with
        docsBpi2CmtsIpMulticastMask.  The type of this address is
        determined by the value of the object
        docsBpi2CmtsIpMulticastAddressType.
        Note: For IPv6, this object need not represent a
        contiguous netmask; e.g., to associate a SAID to a
        multicast group matching 'any' multicast scope.  The TC

        InetAddressPrefixLength is not used, as it only
        represents contiguous netmask."
        ::= { docsBpi2CmtsIpMulticastMapEntry 4 }

   docsBpi2CmtsIpMulticastSAId        OBJECT-TYPE
        SYNTAX         DocsSAIdOrZero
        MAX-ACCESS     read-create
        STATUS         current
        DESCRIPTION
             "This object represents the multicast SAID to be
        used in this IP multicast address mapping entry."
        ::= { docsBpi2CmtsIpMulticastMapEntry 5 }

   docsBpi2CmtsIpMulticastSAType OBJECT-TYPE
        SYNTAX         DocsBpkmSAType
        MAX-ACCESS     read-create
        STATUS         current
        DESCRIPTION
             "The value of this object is the type of security
        association.  'dynamic' does not apply to CMs running in
        BPI mode.  Unicast BPI TEKs must utilize the 'primary'
        encoding, and multicast BPI TEKs must utilize the 'static'
        encoding.  By default, SNMP created entries set this object
        to 'static' if not set at row creation."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 2.1.3."
        ::= { docsBpi2CmtsIpMulticastMapEntry 6 }

   docsBpi2CmtsIpMulticastDataEncryptAlg   OBJECT-TYPE
        SYNTAX    DocsBpkmDataEncryptAlg
        MAX-ACCESS     read-create
        STATUS         current
        DESCRIPTION
             "The value of this object is the data encryption
        algorithm for this IP."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.2.20."
        DEFVAL { des56CbcMode }
        ::= { docsBpi2CmtsIpMulticastMapEntry 7 }

   docsBpi2CmtsIpMulticastDataAuthentAlg   OBJECT-TYPE
        SYNTAX    DocsBpkmDataAuthentAlg
        MAX-ACCESS     read-create
        STATUS         current
        DESCRIPTION
             "The value of this object is the data authentication

        algorithm for this IP."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.2.20."
        DEFVAL { none }
        ::= { docsBpi2CmtsIpMulticastMapEntry 8 }

   docsBpi2CmtsIpMulticastSAMapRequests    OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the number of times the
        CMTS has received an SA Map Request message for this IP.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.10."
        ::= { docsBpi2CmtsIpMulticastMapEntry 9 }

   docsBpi2CmtsIpMulticastSAMapReplies     OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the number of times the
        CMTS has transmitted an SA Map Reply message for this IP.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other
        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.11."
        ::= { docsBpi2CmtsIpMulticastMapEntry 10 }

   docsBpi2CmtsIpMulticastSAMapRejects     OBJECT-TYPE
        SYNTAX         Counter32
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the number of times the
        CMTS has transmitted an SA Map Reject message for this IP.
        Discontinuities in the value of this counter can occur at
        re-initialization of the management system, and at other

        times as indicated by the value of
        ifCounterDiscontinuityTime."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 4.2.1.12."
        ::= { docsBpi2CmtsIpMulticastMapEntry 11 }

   docsBpi2CmtsIpMulticastSAMapRejectErrorCode  OBJECT-TYPE
        SYNTAX         INTEGER {
                               none(1),
                               unknown(2),
                               noAuthForRequestedDSFlow(9),
                               dsFlowNotMappedToSA(10)
                               }
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the enumerated
        description of the Error-Code in the most recent SA Map
        Reject message sent in response to an SA Map Request for
        this IP.  It has the value unknown(2) if the last Error-Code
        Value was 0 and none(1) if no SA MAP Reject message has
        been received since entry creation."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.1.12 and 4.2.2.15."
        ::= { docsBpi2CmtsIpMulticastMapEntry 12 }

   docsBpi2CmtsIpMulticastSAMapRejectErrorString     OBJECT-TYPE
        SYNTAX         SnmpAdminString (SIZE (0..128))
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The value of this object is the text string in
        the most recent SA Map Reject message sent in response to
        an SA Map Request for this IP.  It is a zero length string
        if no SA Map Reject message has been received since entry
        creation."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections 4.2.1.12 and 4.2.2.6."
        ::= { docsBpi2CmtsIpMulticastMapEntry 13 }

   docsBpi2CmtsIpMulticastMapControl  OBJECT-TYPE
        SYNTAX         RowStatus
        MAX-ACCESS     read-create
        STATUS         current
        DESCRIPTION
             "This object controls and reflects the IP multicast
        address mapping entry.  There is no restriction on the
        ability to change values in this row while the row is
        active.
        A created row can be set to active only after the
        Corresponding instances of docsBpi2CmtsIpMulticastAddress,
        docsBpi2CmtsIpMulticastMask, docsBpi2CmtsIpMulticastSAId,
        and docsBpi2CmtsIpMulticastSAType have all been set."
        ::= { docsBpi2CmtsIpMulticastMapEntry 14 }

   docsBpi2CmtsIpMulticastMapStorageType     OBJECT-TYPE
        SYNTAX         StorageType
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The storage type for this conceptual row.
        Conceptual rows having the value 'permanent' need not allow
        write-access to any columnar objects in the row."
        ::= { docsBpi2CmtsIpMulticastMapEntry 15 }

   --
   -- The CMTS Multicast SAID Authorization Table,
   -- indexed by ifIndex by
   -- multicast SAID by CM MAC address
   --

   docsBpi2CmtsMulticastAuthTable          OBJECT-TYPE
        SYNTAX         SEQUENCE OF DocsBpi2CmtsMulticastAuthEntry
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
             "This table describes the multicast SAID
        authorization for each CM on each CMTS MAC interface."
        ::= { docsBpi2CmtsMulticastObjects 2 }

   docsBpi2CmtsMulticastAuthEntry          OBJECT-TYPE
        SYNTAX         DocsBpi2CmtsMulticastAuthEntry
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
             "Each entry contains objects describing the key
        authorization of one cable modem for one multicast SAID
        for one CMTS MAC interface.
        Row entries persist after re-initialization of
        the managed system."
        INDEX     { ifIndex, docsBpi2CmtsMulticastAuthSAId,
               docsBpi2CmtsMulticastAuthCmMacAddress }
        ::= { docsBpi2CmtsMulticastAuthTable 1 }

   DocsBpi2CmtsMulticastAuthEntry ::= SEQUENCE
        {
        docsBpi2CmtsMulticastAuthSAId                DocsSAId,
        docsBpi2CmtsMulticastAuthCmMacAddress        MacAddress,
        docsBpi2CmtsMulticastAuthControl             RowStatus
        }

   docsBpi2CmtsMulticastAuthSAId OBJECT-TYPE
        SYNTAX         DocsSAId
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
             "This object represents the multicast SAID for
        authorization."
        ::= { docsBpi2CmtsMulticastAuthEntry 1 }

   docsBpi2CmtsMulticastAuthCmMacAddress   OBJECT-TYPE
        SYNTAX         MacAddress
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
             "This object represents the MAC address of the CM
        to which the multicast SAID authorization applies."
        ::= { docsBpi2CmtsMulticastAuthEntry 2 }

   docsBpi2CmtsMulticastAuthControl   OBJECT-TYPE
        SYNTAX         RowStatus
        MAX-ACCESS     read-create
        STATUS         current
        DESCRIPTION
             "The status of this conceptual row for the
        authorization of multicast SAIDs to CMs."
        ::= { docsBpi2CmtsMulticastAuthEntry 3 }

   --
   -- CMTS Cert Objects
   --

   docsBpi2CmtsCertObjects OBJECT IDENTIFIER
        ::= { docsBpi2CmtsObjects 5 }

   --
   -- CMTS Provisioned CM Cert Table
   --

   docsBpi2CmtsProvisionedCmCertTable OBJECT-TYPE
        SYNTAX         SEQUENCE OF
                        DocsBpi2CmtsProvisionedCmCertEntry
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
             "A table of CM certificate trust entries provisioned
        to the CMTS.  The trust object for a certificate in this
        table has an overriding effect on the validity object of a
        certificate in the authorization table, as long as the
        entire contents of the two certificates are identical."
        ::= { docsBpi2CmtsCertObjects 1 }

   docsBpi2CmtsProvisionedCmCertEntry OBJECT-TYPE
        SYNTAX         DocsBpi2CmtsProvisionedCmCertEntry
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
             "An entry in the CMTS's provisioned CM certificate
        table.  Row entries persist after re-initialization of
        the managed system."
        REFERENCE
             "Data-Over-Cable Service Interface Specifications:
        Operations Support System Interface Specification
        SP-OSSIv2.0-I05-040407, Section 6.2.14"
        INDEX { docsBpi2CmtsProvisionedCmCertMacAddress }
        ::= { docsBpi2CmtsProvisionedCmCertTable 1 }

   DocsBpi2CmtsProvisionedCmCertEntry ::= SEQUENCE
        {
        docsBpi2CmtsProvisionedCmCertMacAddress MacAddress,
        docsBpi2CmtsProvisionedCmCertTrust      INTEGER,
        docsBpi2CmtsProvisionedCmCertSource     INTEGER,
        docsBpi2CmtsProvisionedCmCertStatus     RowStatus,
        docsBpi2CmtsProvisionedCmCert
                                  DocsX509ASN1DEREncodedCertificate
        }

   docsBpi2CmtsProvisionedCmCertMacAddress OBJECT-TYPE
        SYNTAX         MacAddress
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
             "The index of this row."
        ::= { docsBpi2CmtsProvisionedCmCertEntry 1 }

   docsBpi2CmtsProvisionedCmCertTrust      OBJECT-TYPE
        SYNTAX    INTEGER {
                          trusted(1),
                          untrusted(2)
                          }
        MAX-ACCESS     read-create
        STATUS    current
        DESCRIPTION
             "Trust state for the provisioned CM certificate entry.
        Note: Setting this object need only override the validity
        of CM certificates sent in future authorization requests;
        instantaneous effect need not occur."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 9.4.1."
        DEFVAL { untrusted }
        ::= { docsBpi2CmtsProvisionedCmCertEntry 2 }

   docsBpi2CmtsProvisionedCmCertSource     OBJECT-TYPE
        SYNTAX    INTEGER {
                          snmp(1),
                          configurationFile(2),
                          externalDatabase(3),
                          other(4)
                          }
        MAX-ACCESS read-only
        STATUS  current
        DESCRIPTION
             "This object indicates how the certificate reached the
        CMTS.  Other(4) means that it originated from a source not
        identified above."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 9.4.1."
        ::= { docsBpi2CmtsProvisionedCmCertEntry 3 }

   docsBpi2CmtsProvisionedCmCertStatus OBJECT-TYPE
        SYNTAX  RowStatus
        MAX-ACCESS read-create
        STATUS  current
        DESCRIPTION
             "The status of this conceptual row.  Values in this row
        cannot be changed while the row is 'active'."
        ::= { docsBpi2CmtsProvisionedCmCertEntry 4 }

   docsBpi2CmtsProvisionedCmCert OBJECT-TYPE
        SYNTAX         DocsX509ASN1DEREncodedCertificate
        MAX-ACCESS     read-create
        STATUS         current
        DESCRIPTION
             "An X509 DER-encoded Certificate Authority
        certificate.
        Note: The zero-length OCTET STRING must be returned, on

        reads, if the entire certificate is not retained in the
        CMTS."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 9.2."
        ::= { docsBpi2CmtsProvisionedCmCertEntry 5 }

   --
   -- CMTS CA Cert Table
   --

   docsBpi2CmtsCACertTable OBJECT-TYPE
        SYNTAX         SEQUENCE OF DocsBpi2CmtsCACertEntry
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
             "The table of known Certificate Authority certificates
        acquired by this device."
        ::= { docsBpi2CmtsCertObjects 2 }

   docsBpi2CmtsCACertEntry OBJECT-TYPE
        SYNTAX         DocsBpi2CmtsCACertEntry
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
             "A row in the Certificate Authority certificate
        table.  Row entries with the trust status 'trusted',
        'untrusted', or 'root' persist after re-initialization
         of the managed system."
        REFERENCE
             "Data-Over-Cable Service Interface Specifications:
        Operations Support System Interface Specification
        SP-OSSIv2.0-I05-040407, Section 6.2.14"
        INDEX   { docsBpi2CmtsCACertIndex }
        ::= {docsBpi2CmtsCACertTable 1 }

   DocsBpi2CmtsCACertEntry ::= SEQUENCE {
        docsBpi2CmtsCACertIndex            Unsigned32,
        docsBpi2CmtsCACertSubject          SnmpAdminString,
        docsBpi2CmtsCACertIssuer           SnmpAdminString,
        docsBpi2CmtsCACertSerialNumber     OCTET STRING,
        docsBpi2CmtsCACertTrust            INTEGER,
        docsBpi2CmtsCACertSource           INTEGER,
        docsBpi2CmtsCACertStatus           RowStatus,
        docsBpi2CmtsCACert
                              DocsX509ASN1DEREncodedCertificate,
        docsBpi2CmtsCACertThumbprint       OCTET STRING
   }

   docsBpi2CmtsCACertIndex OBJECT-TYPE
        SYNTAX         Unsigned32 (1.. 4294967295)
        MAX-ACCESS     not-accessible
        STATUS         current
        DESCRIPTION
             "The index for this row."
        ::= { docsBpi2CmtsCACertEntry 1 }

   docsBpi2CmtsCACertSubject OBJECT-TYPE
        SYNTAX         SnmpAdminString
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The subject name exactly as it is encoded in the
        X509 certificate.
        The organizationName portion of the certificate's subject
        name must be present.  All other fields are optional.  Any
        optional field present must be prepended with <CR>
        (carriage return, U+000D) <LF> (line feed, U+000A).
        Ordering of fields present must conform to the following:

        organizationName <CR> <LF>
        countryName <CR> <LF>
        stateOrProvinceName <CR> <LF>
        localityName <CR> <LF>
        organizationalUnitName <CR> <LF>
        organizationalUnitName=<Manufacturing Location> <CR> <LF>
        commonName"
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 9.2.4"
        ::= { docsBpi2CmtsCACertEntry 2 }

   docsBpi2CmtsCACertIssuer OBJECT-TYPE
        SYNTAX         SnmpAdminString
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The issuer name exactly as it is encoded in the
        X509 certificate.
        The commonName portion of the certificate's issuer
        name must be present.  All other fields are optional.  Any
        optional field present must be prepended with <CR>
        (carriage return, U+000D) <LF> (line feed, U+000A).
        Ordering of fields present must conform to the following:

        CommonName <CR><LF>
        countryName <CR><LF>

        stateOrProvinceName <CR><LF>
        localityName <CR><LF>
        organizationName <CR><LF>
        organizationalUnitName <CR><LF>
        organizationalUnitName=<Manufacturing Location>"
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 9.2.4"
        ::= { docsBpi2CmtsCACertEntry 3 }

   docsBpi2CmtsCACertSerialNumber OBJECT-TYPE
        SYNTAX         OCTET STRING (SIZE (1..32))
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "This CA certificate's serial number, represented as
        an octet string."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 9.2.2"
        ::= { docsBpi2CmtsCACertEntry 4 }

   docsBpi2CmtsCACertTrust OBJECT-TYPE
        SYNTAX    INTEGER {
                          trusted (1),
                          untrusted (2),
                          chained (3),
                          root (4)
                          }
        MAX-ACCESS     read-create
        STATUS    current
        DESCRIPTION
             "This object controls the trust status of this
        certificate.  Root certificates must be given root(4)
        trust; manufacturer certificates must not be given root(4)
        trust.  Trust on root certificates must not change.
        Note: Setting this object need only affect the validity of
        CM certificates sent in future authorization requests;
        instantaneous effect need not occur."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 9.4.1"
        DEFVAL { chained }
        ::= { docsBpi2CmtsCACertEntry 5 }

   docsBpi2CmtsCACertSource OBJECT-TYPE
        SYNTAX    INTEGER {
                  snmp (1),
                  configurationFile (2),
                  externalDatabase (3),
                  other (4),
                  authentInfo (5),
                  compiledIntoCode (6)
                  }
        MAX-ACCESS     read-only
        STATUS    current
        DESCRIPTION
             "This object indicates how the certificate reached
        the CMTS.  Other(4) means that it originated from a source
        not identified above."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 9.4.1"
        ::= { docsBpi2CmtsCACertEntry 6 }

   docsBpi2CmtsCACertStatus OBJECT-TYPE
        SYNTAX         RowStatus
        MAX-ACCESS     read-create
        STATUS         current
        DESCRIPTION
             "The status of this conceptual row.  An attempt
        to set writable columnar values while this row is active
        behaves as follows:
        - Sets to the object docsBpi2CmtsCACertTrust are allowed.
        - Sets to the object docsBpi2CmtsCACert will return an
          error of 'inconsistentValue'.
        A newly created entry cannot be set to active until the
        value of docsBpi2CmtsCACert is being set."
        ::= { docsBpi2CmtsCACertEntry 7 }

   docsBpi2CmtsCACert  OBJECT-TYPE
        SYNTAX         DocsX509ASN1DEREncodedCertificate
        MAX-ACCESS     read-create
        STATUS         current
        DESCRIPTION
             "An X509 DER-encoded Certificate Authority
        certificate.
        To help identify certificates, either this object or
        docsBpi2CmtsCACertThumbprint must be returned by a CMTS for
        self-signed CA certificates.

        Note: The zero-length OCTET STRING must be returned, on
        reads, if the entire certificate is not retained in the
        CMTS."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 9.2."
        ::= { docsBpi2CmtsCACertEntry 8 }

   docsBpi2CmtsCACertThumbprint OBJECT-TYPE
        SYNTAX         OCTET STRING (SIZE (20))
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
             "The SHA-1 hash of a CA certificate.
        To help identify certificates, either this object or
        docsBpi2CmtsCACert must be returned by a CMTS for
        self-signed CA certificates.

        Note: The zero-length OCTET STRING must be returned, on
        reads, if the CA certificate thumb print is not retained
        in the CMTS."
        REFERENCE
             "DOCSIS Baseline Privacy Plus Interface Specification,
        Section 9.4.3"
        ::= { docsBpi2CmtsCACertEntry 9 }

   --
   -- Authenticated Software Download Objects
   --

   --
   -- Note: the authenticated software download objects are a
   -- CM requirement only.
   --

   docsBpi2CodeDownloadControl OBJECT IDENTIFIER
        ::= { docsBpi2MIBObjects 4 }

   docsBpi2CodeDownloadStatusCode     OBJECT-TYPE
        SYNTAX    INTEGER {
                          configFileCvcVerified (1),
                          configFileCvcRejected (2),
                          snmpCvcVerified (3),
                          snmpCvcRejected (4),
                          codeFileVerified (5),
                          codeFileRejected (6),
                          other (7)
                          }
        MAX-ACCESS     read-only
        STATUS    current
        DESCRIPTION
            "The value indicates the result of the latest config
        file CVC verification, SNMP CVC verification, or code file

        verification."
        REFERENCE
            "DOCSIS Baseline Privacy Plus Interface Specification,
        Sections D.3.3.2 and D.3.5.1."
        ::= { docsBpi2CodeDownloadControl 1 }

   docsBpi2CodeDownloadStatusString   OBJECT-TYPE
        SYNTAX         SnmpAdminString
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
            "The value of this object indicates the additional
        information to the status code.  The value will include
        the error code and error description, which will be defined
        separately."
        REFERENCE
            "DOCSIS Baseline Privacy Plus Interface Specification,
        Section D.3.7"
        ::= { docsBpi2CodeDownloadControl 2 }

   docsBpi2CodeMfgOrgName   OBJECT-TYPE
        SYNTAX         SnmpAdminString
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
            "The value of this object is the device manufacturer's
        organizationName."
        REFERENCE
            "DOCSIS Baseline Privacy Plus Interface Specification,
        Section D.3.2.2."
        ::= { docsBpi2CodeDownloadControl 3 }

   docsBpi2CodeMfgCodeAccessStart     OBJECT-TYPE
        SYNTAX         DateAndTime  (SIZE(11))
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
            "The value of this object is the device manufacturer's
        current codeAccessStart value.  This value will always
        refer to Greenwich Mean Time (GMT), and the value
        format must contain TimeZone information (fields 8-10)."
        REFERENCE
            "DOCSIS Baseline Privacy Plus Interface Specification,
        Section D.3.2.2."
        ::= { docsBpi2CodeDownloadControl 4 }

   docsBpi2CodeMfgCvcAccessStart OBJECT-TYPE
        SYNTAX         DateAndTime (SIZE(11))
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
            "The value of this object is the device manufacturer's
        current cvcAccessStart value.  This value will always
        refer to Greenwich Mean Time (GMT), and the value
        format must contain TimeZone information (fields 8-10)."
        REFERENCE
            "DOCSIS Baseline Privacy Plus Interface Specification,
        Section D.3.2.2."
        ::= { docsBpi2CodeDownloadControl 5 }

   docsBpi2CodeCoSignerOrgName   OBJECT-TYPE
        SYNTAX         SnmpAdminString
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
            "The value of this object is the co-signer's
        organizationName.  The value is a zero length string if
        the co-signer is not specified."
        REFERENCE
            "DOCSIS Baseline Privacy Plus Interface Specification,
        Section D.3.2.2."
        ::= { docsBpi2CodeDownloadControl 6 }

   docsBpi2CodeCoSignerCodeAccessStart     OBJECT-TYPE
        SYNTAX         DateAndTime (SIZE(11))
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
            "The value of this object is the co-signer's current
        codeAccessStart value.  This value will always refer to
        Greenwich Mean Time (GMT), and the value format must contain
        TimeZone information (fields 8-10).
        If docsBpi2CodeCoSignerOrgName is a zero
        length string, the value of this object is meaningless."
        REFERENCE
            "DOCSIS Baseline Privacy Plus Interface Specification,
        Section D.3.2.2."
        ::= { docsBpi2CodeDownloadControl 7 }

   docsBpi2CodeCoSignerCvcAccessStart OBJECT-TYPE
        SYNTAX         DateAndTime (SIZE(11))
        MAX-ACCESS     read-only
        STATUS         current
        DESCRIPTION
            "The value of this object is the co-signer's current
        cvcAccessStart value.  This value will always refer to

        Greenwich Mean Time (GMT), and the value format must contain
        TimeZone information (fields 8-10).
        If docsBpi2CodeCoSignerOrgName is a zero
        length string, the value of this object is meaningless."
        REFERENCE
            "DOCSIS Baseline Privacy Plus Interface Specification,
        Section D.3.2.2."
        ::= { docsBpi2CodeDownloadControl 8 }

   docsBpi2CodeCvcUpdate    OBJECT-TYPE
        SYNTAX         DocsX509ASN1DEREncodedCertificate
        MAX-ACCESS     read-write
        STATUS         current
        DESCRIPTION
            "Setting a CVC to this object triggers the device
        to verify the CVC and update the cvcAccessStart values.
        The content of this object is then discarded.
        If the device is not enabled to upgrade codefiles, or if
        the CVC verification fails, the CVC will be rejected.
        Reading this object always returns the zero-length OCTET
        STRING."
        REFERENCE
            "DOCSIS Baseline Privacy Plus Interface Specification,
        Section D.3.3.2.2."
        ::= { docsBpi2CodeDownloadControl 9 }

   --
   -- The BPI+ MIB Conformance Statements (with a placeholder for
   -- notifications)
   --

   docsBpi2Notification     OBJECT IDENTIFIER
        ::= { docsBpi2MIB 0 }
   docsBpi2Conformance OBJECT IDENTIFIER
        ::= { docsBpi2MIB 2 }
   docsBpi2Compliances OBJECT IDENTIFIER
        ::= { docsBpi2Conformance 1 }
   docsBpi2Groups      OBJECT IDENTIFIER
        ::= { docsBpi2Conformance 2 }

   docsBpi2CmCompliance MODULE-COMPLIANCE
        STATUS         current
        DESCRIPTION
             "This is the compliance statement for CMs that
        implement the DOCSIS Baseline Privacy Interface Plus."

        MODULE  -- docsBpi2MIB

        -- unconditionally mandatory group
        MANDATORY-GROUPS {
               docsBpi2CmGroup,
               docsBpi2CodeDownloadGroup
        }

   -- constrain on Encryption algorithms
   OBJECT docsBpi2CmTEKDataEncryptAlg
        SYNTAX    DocsBpkmDataEncryptAlg {
                               none(0),
                               des56CbcMode(1),
                               des40CbcMode(2)
                  }
        DESCRIPTION
             "It is compliant to support des56CbcMode(1) and
        des40CbcMode(2) for data encryption algorithms."

   -- constrain on Integrity algorithms
   OBJECT docsBpi2CmTEKDataAuthentAlg
        SYNTAX    DocsBpkmDataAuthentAlg {
                               none(0)
                  }
        DESCRIPTION
             "It is compliant to not support data message
        authentication algorithms."

   -- constrain on IP addressing
   OBJECT    docsBpi2CmIpMulticastAddressType
        SYNTAX InetAddressType { ipv4(1) }
        DESCRIPTION
             "An implementation is only required to support IPv4
        addresses.  Support for other address types may be defined
        in future versions of this MIB module."

   -- constrain on IP addressing
   OBJECT    docsBpi2CmIpMulticastAddress
        SYNTAX  InetAddress (SIZE(4))
        DESCRIPTION
             "An implementation is only required to support IPv4
        addresses Other address types support may be defined in
        future versions of this MIB module."

   -- constrain on Encryption algorithms
   OBJECT docsBpi2CmCryptoSuiteDataEncryptAlg
        SYNTAX    DocsBpkmDataEncryptAlg {
                               none(0),
                               des56CbcMode(1),
                               des40CbcMode(2)

                  }
        DESCRIPTION
             "It is compliant to only support des56CbcMode(1)
        and des40CbcMode(2) for data encryption algorithms."

   -- constrain on Integrity algorithms
   OBJECT docsBpi2CmCryptoSuiteDataAuthentAlg
        SYNTAX    DocsBpkmDataAuthentAlg {
                               none(0)
                  }
        DESCRIPTION
             "It is compliant to not support data message
        authentication algorithms."
   ::= { docsBpi2Compliances 1 }

   docsBpi2CmtsCompliance MODULE-COMPLIANCE
        STATUS         current
        DESCRIPTION
             "This is the compliance statement for CMTSs that
        implement the DOCSIS Baseline Privacy Interface Plus."

        MODULE  -- docsBpi2MIB
        -- unconditionally mandatory group
        MANDATORY-GROUPS {
               docsBpi2CmtsGroup
        }

   -- unconditionally optional group
   GROUP     docsBpi2CodeDownloadGroup
        DESCRIPTION
             "This group is optional for CMTSes.  The implementation
        decision of this group is left to the vendor"

   -- constrain on mandatory range

   OBJECT    docsBpi2CmtsDefaultAuthLifetime
        SYNTAX    Integer32 (86400..6048000)
        DESCRIPTION
             "The refined range corresponds to the minimum and
        maximum values in operational networks."

   -- constrain on mandatory range

   OBJECT    docsBpi2CmtsDefaultTEKLifetime
        SYNTAX    Integer32 (1800..604800)
        DESCRIPTION
            "The refined range corresponds to the minimum and
        maximum values in operational networks."

   -- constrain on mandatory range

   OBJECT    docsBpi2CmtsAuthCmLifetime
        SYNTAX    Integer32 (86400..6048000)
        DESCRIPTION
            "The refined range corresponds to the minimum and
        maximum values in operational networks."

   -- constrain on Encryption algorithms

OBJECT   docsBpi2CmtsTEKDataEncryptAlg
        SYNTAX    DocsBpkmDataEncryptAlg {
                               none(0),
                               des56CbcMode(1),
                               des40CbcMode(2)
                  }
        DESCRIPTION
             "It is compliant to only support des56CbcMode(1)
        and des40CbcMode(2) for data encryption."

   -- constrain on Integrity algorithms

OBJECT docsBpi2CmtsTEKDataAuthentAlg
        SYNTAX    DocsBpkmDataAuthentAlg {
                               none(0)
                  }
        DESCRIPTION
             "It is compliant to not support data message
        authentication algorithms."

   -- constrain on mandatory range

   OBJECT    docsBpi2CmtsTEKLifetime
        SYNTAX    Integer32 (1800..604800)
        DESCRIPTION
            "The refined range corresponds to the minimum and
        maximum values in operational networks."

   -- constrain on access
   -- constrain on IP Addressing

   OBJECT    docsBpi2CmtsIpMulticastAddressType
        SYNTAX      InetAddressType { ipv4(1) }
        MIN-ACCESS  read-only
        DESCRIPTION
            "Write access is not required.
        An implementation is only required to support IPv4
        addresses.  Support for other address types may be defined
        in future versions of this MIB module."

   OBJECT    docsBpi2CmtsIpMulticastAddress
        SYNTAX  InetAddress (SIZE(4))
        MIN-ACCESS  read-only
        DESCRIPTION
            "Write access is not required.
        An implementation is only required to support IPv4
        addresses.  Support for other address types may be defined
        in future versions of this MIB module."

   OBJECT    docsBpi2CmtsIpMulticastMask
        SYNTAX  InetAddress (SIZE(4))
        MIN-ACCESS  read-only
        DESCRIPTION
            "Write access is not required.
        An implementation is only required to support IPv4
        addresses.  Support for other address types may be defined
        in future versions of this MIB module."

   -- constrain on access

   OBJECT    docsBpi2CmtsIpMulticastSAId
        MIN-ACCESS  read-only
        DESCRIPTION
            "Write access is not required."

   OBJECT    docsBpi2CmtsIpMulticastSAType
        MIN-ACCESS  read-only
        DESCRIPTION
            "Write access is not required."

   -- constrain on access
   -- constrain on Encryption algorithms

   OBJECT    docsBpi2CmtsIpMulticastDataEncryptAlg
        SYNTAX    DocsBpkmDataEncryptAlg {
                               none(0),
                               des56CbcMode(1),
                               des40CbcMode(2)
                  }
        MIN-ACCESS  read-only
        DESCRIPTION
            "Write access is not required.
        It is compliant to only support des56CbcMode(1)

        and des40CbcMode(2) for data encryption"

   -- constrain on access
   -- constrain on Integrity algorithms

   OBJECT    docsBpi2CmtsIpMulticastDataAuthentAlg
        SYNTAX    DocsBpkmDataAuthentAlg {
                               none(0)
                  }
        MIN-ACCESS  read-only
        DESCRIPTION
            "Write access is not required.
        It is compliant to not support data message
        authentication algorithms."

   -- constrain on access

   OBJECT    docsBpi2CmtsMulticastAuthControl
        MIN-ACCESS  read-only
        DESCRIPTION
       "Write access is not required."
        ::= { docsBpi2Compliances 2 }

   docsBpi2CmGroup     OBJECT-GROUP
        OBJECTS   {
             docsBpi2CmPrivacyEnable,
             docsBpi2CmPublicKey,
             docsBpi2CmAuthState,
             docsBpi2CmAuthKeySequenceNumber,
             docsBpi2CmAuthExpiresOld,
             docsBpi2CmAuthExpiresNew,
             docsBpi2CmAuthReset,
             docsBpi2CmAuthGraceTime,
             docsBpi2CmTEKGraceTime,
             docsBpi2CmAuthWaitTimeout,
             docsBpi2CmReauthWaitTimeout,
             docsBpi2CmOpWaitTimeout,
             docsBpi2CmRekeyWaitTimeout,
             docsBpi2CmAuthRejectWaitTimeout,
             docsBpi2CmSAMapWaitTimeout,
             docsBpi2CmSAMapMaxRetries,
             docsBpi2CmAuthentInfos,
             docsBpi2CmAuthRequests,
             docsBpi2CmAuthReplies,
             docsBpi2CmAuthRejects,
             docsBpi2CmAuthInvalids,
             docsBpi2CmAuthRejectErrorCode,
             docsBpi2CmAuthRejectErrorString,
             docsBpi2CmAuthInvalidErrorCode,
             docsBpi2CmAuthInvalidErrorString,
             docsBpi2CmTEKSAType,
             docsBpi2CmTEKDataEncryptAlg,
             docsBpi2CmTEKDataAuthentAlg,
             docsBpi2CmTEKState,
             docsBpi2CmTEKKeySequenceNumber,
             docsBpi2CmTEKExpiresOld,
             docsBpi2CmTEKExpiresNew,
             docsBpi2CmTEKKeyRequests,
             docsBpi2CmTEKKeyReplies,
             docsBpi2CmTEKKeyRejects,
             docsBpi2CmTEKInvalids,
             docsBpi2CmTEKAuthPends,
             docsBpi2CmTEKKeyRejectErrorCode,
             docsBpi2CmTEKKeyRejectErrorString,
             docsBpi2CmTEKInvalidErrorCode,
             docsBpi2CmTEKInvalidErrorString,
             docsBpi2CmIpMulticastAddressType,
             docsBpi2CmIpMulticastAddress,
             docsBpi2CmIpMulticastSAId,
             docsBpi2CmIpMulticastSAMapState,
             docsBpi2CmIpMulticastSAMapRequests,
             docsBpi2CmIpMulticastSAMapReplies,
             docsBpi2CmIpMulticastSAMapRejects,
             docsBpi2CmIpMulticastSAMapRejectErrorCode,
             docsBpi2CmIpMulticastSAMapRejectErrorString,
             docsBpi2CmDeviceCmCert,
             docsBpi2CmDeviceManufCert,
             docsBpi2CmCryptoSuiteDataEncryptAlg,
             docsBpi2CmCryptoSuiteDataAuthentAlg
             }
        STATUS         current
        DESCRIPTION
             "This collection of objects provides CM BPI+ status
        and control."
   ::= { docsBpi2Groups 1 }

   docsBpi2CmtsGroup   OBJECT-GROUP
        OBJECTS {
             docsBpi2CmtsDefaultAuthLifetime,
             docsBpi2CmtsDefaultTEKLifetime,
             docsBpi2CmtsDefaultSelfSignedManufCertTrust,
             docsBpi2CmtsCheckCertValidityPeriods,
             docsBpi2CmtsAuthentInfos,
             docsBpi2CmtsAuthRequests,
             docsBpi2CmtsAuthReplies,
             docsBpi2CmtsAuthRejects,
             docsBpi2CmtsAuthInvalids,
             docsBpi2CmtsSAMapRequests,
             docsBpi2CmtsSAMapReplies,
             docsBpi2CmtsSAMapRejects,
             docsBpi2CmtsAuthCmBpiVersion,
             docsBpi2CmtsAuthCmPublicKey,
             docsBpi2CmtsAuthCmKeySequenceNumber,
             docsBpi2CmtsAuthCmExpiresOld,
             docsBpi2CmtsAuthCmExpiresNew,
             docsBpi2CmtsAuthCmLifetime,
             docsBpi2CmtsAuthCmReset,
             docsBpi2CmtsAuthCmInfos,
             docsBpi2CmtsAuthCmRequests,
             docsBpi2CmtsAuthCmReplies,
             docsBpi2CmtsAuthCmRejects,
             docsBpi2CmtsAuthCmInvalids,
             docsBpi2CmtsAuthRejectErrorCode,
             docsBpi2CmtsAuthRejectErrorString,
             docsBpi2CmtsAuthInvalidErrorCode,
             docsBpi2CmtsAuthInvalidErrorString,
             docsBpi2CmtsAuthPrimarySAId,
             docsBpi2CmtsAuthBpkmCmCertValid,
             docsBpi2CmtsAuthBpkmCmCert,
             docsBpi2CmtsAuthCACertIndexPtr,
             docsBpi2CmtsTEKSAType,
             docsBpi2CmtsTEKDataEncryptAlg,
             docsBpi2CmtsTEKDataAuthentAlg,
             docsBpi2CmtsTEKLifetime,
             docsBpi2CmtsTEKKeySequenceNumber,
             docsBpi2CmtsTEKExpiresOld,
             docsBpi2CmtsTEKExpiresNew,
             docsBpi2CmtsTEKReset,
             docsBpi2CmtsKeyRequests,
             docsBpi2CmtsKeyReplies,
             docsBpi2CmtsKeyRejects,
             docsBpi2CmtsTEKInvalids,
             docsBpi2CmtsKeyRejectErrorCode,
             docsBpi2CmtsKeyRejectErrorString,
             docsBpi2CmtsTEKInvalidErrorCode,
             docsBpi2CmtsTEKInvalidErrorString,
             docsBpi2CmtsIpMulticastAddressType,
             docsBpi2CmtsIpMulticastAddress,
             docsBpi2CmtsIpMulticastMask,
             docsBpi2CmtsIpMulticastSAId,
             docsBpi2CmtsIpMulticastSAType,
             docsBpi2CmtsIpMulticastDataEncryptAlg,
             docsBpi2CmtsIpMulticastDataAuthentAlg,
             docsBpi2CmtsIpMulticastSAMapRequests,
             docsBpi2CmtsIpMulticastSAMapReplies,
             docsBpi2CmtsIpMulticastSAMapRejects,
             docsBpi2CmtsIpMulticastSAMapRejectErrorCode,
             docsBpi2CmtsIpMulticastSAMapRejectErrorString,
             docsBpi2CmtsIpMulticastMapControl,
             docsBpi2CmtsIpMulticastMapStorageType,
             docsBpi2CmtsMulticastAuthControl,
             docsBpi2CmtsProvisionedCmCertTrust,
             docsBpi2CmtsProvisionedCmCertSource,
             docsBpi2CmtsProvisionedCmCertStatus,
             docsBpi2CmtsProvisionedCmCert,
             docsBpi2CmtsCACertSubject,
             docsBpi2CmtsCACertIssuer,
             docsBpi2CmtsCACertSerialNumber,
             docsBpi2CmtsCACertTrust,
             docsBpi2CmtsCACertSource,
             docsBpi2CmtsCACertStatus,
             docsBpi2CmtsCACert,
             docsBpi2CmtsCACertThumbprint
             }
        STATUS         current
        DESCRIPTION
             "This collection of objects provides CMTS BPI+ status
        and control."
   ::= { docsBpi2Groups 2 }

   docsBpi2CodeDownloadGroup OBJECT-GROUP
           OBJECTS {
             docsBpi2CodeDownloadStatusCode,
             docsBpi2CodeDownloadStatusString,
             docsBpi2CodeMfgOrgName,
             docsBpi2CodeMfgCodeAccessStart,
             docsBpi2CodeMfgCvcAccessStart,
             docsBpi2CodeCoSignerOrgName,
             docsBpi2CodeCoSignerCodeAccessStart,
             docsBpi2CodeCoSignerCvcAccessStart,
             docsBpi2CodeCvcUpdate
             }
        STATUS         current
        DESCRIPTION
             "This collection of objects provides authenticated
        software download support."
   ::= { docsBpi2Groups 3 }

   END